Jump to content
SAU Community

Where To Get Braided Lines?

sloutch

By sloutch,
in Victoria

 Share

Recommended Posts

some_cs_student Veteran

some_cs_student

Posted
Posted
Hi guys,

am wondering where can i get braided lines custom made in different lengths in Melbourne?

And yes i tried doing a search and using Advance Search. :)

Thanks!

Hmm, I don't have the company who did my custom brake lines written down, but they were ADR approved.

There are a few places that do them, including that one in Sunshine (Brakewest).

There are also some local places in the South Eastern suburbs, I assume they'd be in the yellow pages....but if you can't find someone I'll try and find out who it was.

SS8_Gohan Grand Master

SS8_Gohan

Posted
Posted

re: braided lines for track applications.

Generally speaking, ADR approved lines AREN'T up to scratch for track work (method of construction), very light track work yes, anything above that.... no

Conversely, CAMS approved braided lines generally speaking AREN'T ADR approved, hence illegal to run in a street car.

I reckon you'd be unlucky to get pinged for em, so if you plan on doing any extended periods of track work, get CAMS approved ones.

I don't know the specifics, but the "crimping" method used to make ADR approved lines (adr approved lines will have a rubber bit with the ADR number stamped on it) doesn't cope with heavy use

some_cs_student Veteran

some_cs_student

Posted
Posted
re: braided lines for track applications.

Generally speaking, ADR approved lines AREN'T up to scratch for track work (method of construction), very light track work yes, anything above that.... no

Apologies for side-tracking the topic but where did you hear that?

I've got a Japanese set of braided lines I'm selling, but if the ADR lines aren't that good I might keep the Japanese set.

SS8_Gohan Grand Master

SS8_Gohan

Posted
Posted

Race Brakes (or whoever the SAU sponsor is) and confirmed by the maker of the group buy braided lines at Brake West (sunshine)

Race Brakes make lines for the V8 Supercars, and he explained the difference between a "street" braided line, and a track braided line.

Brake West said they can replace the rubber ADR fittings with metal ones (on the GB lines) to comply with CAMS, but then it's no longer ADR approved.

But you'd prob have to have a switched on officer to know though.... i reckon....

some_cs_student Veteran

some_cs_student

Posted
Posted
Brake West said they can replace the rubber ADR fittings with metal ones (on the GB lines) to comply with CAMS, but then it's no longer ADR approved.

But you'd prob have to have a switched on officer to know though.... i reckon....

Interesting, I'm not concerned about defects, my lines look like there plastic (black plastic coating over plastic over braided line), my concern is insurance.

Saying I couldn't stop because I didn't have ADR approved lines if something ever happened would be an issue.

Thanks for the information.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
×
×
  • Create New...