Jump to content
SAU Community

My Two Rim Choices

Adz2332

By Adz2332,
in Exterior & Interior Styling

 Share

Recommended Posts

Adz2332 Grand Master

Adz2332

Posted
Posted (edited)

Hey

This is what i narrowed my wheel choice down to. Work XD9s or Rays 57 Pro. 18x10 +20.

My GTR R33 is in midnight purple.

They are both roughly the same price ive found. Any ideas what colours these come in?

Also i have sent some emails for quotes, neugen and greenline.

Any ideas who else i could contact to get a quote would be much appreciated.

Thanks guys.

post-33454-1212800491.jpg

post-33454-1212800505.jpg

Edited by Adz2332
Link to comment
https://www.sau.com.au/forums/topic/222741-my-two-rim-choices/
Share on other sites
Al Grand Master

Al

Posted
Posted

Not 100% sure if these are XD9's, but you get an idea how they look.

Car pictured is also a midnight purple GTR, but hard to see due to an overcast day.

Looks tough as in person.

I also love the 57pro's; either way you go it wont be a bad decision :cheers:

post-1811-1212977013_thumb.jpg

RustyR32Gtst Mentor

RustyR32Gtst

Posted
Posted (edited)
Yer i dunno.... they both roughly cost the same.. both look hot :S

any ideas who i can ask for a quote on eother of the rims??

Try these guys -

http://www.musecret.com.au/

http://www.skylinesaustralia.com/forums/Wo...ml#entry3023917

Edited by SNISMO

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      What accelerator cable can be used with greddy plenum

      By Duncan · Posted

      I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...