Jump to content
SAU Community

Recommended Posts

I've got an r32 rb25 head and was wondering if anyone who has used one of these heads can help me out with where to get an inlet manifold gasket to suit. i posted this before and was told to go to nissan directly, i gave them a call and was told it would be 4 to 6 weeks and 80 bucks. someone also mentioned gizzmo but they didn't mention that head on their website. Should i just order one from nissan?

Link to comment
https://www.sau.com.au/forums/topic/223237-r32-rb25-head-on-2530/
Share on other sites

  • 3 weeks later...
  • 2 weeks later...

The R32 RB25DE VRS kit is worth around $280 from Nissan.

Comes with all gaskets.

Or reuse the old with a spray of Hylomar if need be.

The plenum to inlet manifold gaskets are around $11; exhaust manifold gaskets are $90 odd but there are some floating around aftermarket that appear 'ok' for cheap.

The R32 Rb25de inlet ports from memory are 5mm larger each side (10mm in total) compared to the rb20det inlet ports. From memory that is its been a while. :D

The R32 RB25DE VRS kit is worth around $280 from Nissan.

Comes with all gaskets.

Or reuse the old with a spray of Hylomar if need be.

The plenum to inlet manifold gaskets are around $11; exhaust manifold gaskets are $90 odd but there are some floating around aftermarket that appear 'ok' for cheap.

The R32 Rb25de inlet ports from memory are 5mm larger each side (10mm in total) compared to the rb20det inlet ports. From memory that is its been a while. :blush:

My exhaust mani gasket for an R32 RB25DE was $60 from nissan.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...