Jump to content
SAU Community

Low Power?

rad100

By rad100,
in Engines & Forced Induction

 Share

Recommended Posts

rad100 Grand Master

rad100

Posted
Posted

well just got my car back from being tuned...

pulled 189.9rwkw on 14psi....

stock rb20det.

apexi ax53b70 p25

get injectors

zorst with stock cat.

fmic

pump

eboost

rb26dett PFC (modded for rb20)

now is this right?

my tuner said the afm was maxing out (stock green label)

any ideas? would it be the rb26dett PFC?

any ideas?

cheers adrian

Link to comment
https://www.sau.com.au/forums/topic/223431-low-power/
Share on other sites
Roy Grand Master

Roy

Posted
Posted

Who tuned it? The eboost looks like it needs lots of work! Hits 11psi at a reasonable rev then creeps up to 14psi. All things considered it looks more like a boost control problem, but if you drop the exhaust inc the cat it will be a good cheap test of whether the std cat is killing power like you would expect.

But yeh, boost control needs work, dump the exhaust and then ask the tuner why is it only making the power it is ...that is of course after you have replaced the AFM

Link to comment
https://www.sau.com.au/forums/topic/223431-low-power/#findComment-3936546
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • BASHERnissan
      TPS voltage RB25DET

      By BASHERnissan · Posted

      Hi guys my TPS voltage is reading over 2v at idle.  My Haltech ECU is reading around 40% throttle position at idle also which is really strange. Note the actual throttle position sensor is brand new…    anyone have any experience with this or know how to calibrate it on Haltech ? 
    • joshuaho96
      Cas issue

      By joshuaho96 · Posted

      The OEM disk will not work on any AEM ECU, you need to use the one they made. You shouldn't have to flip the CAS or whatever you were describing, if you set the ignition sync offset correctly it can't backfire. Make sure you're using a spark plug lead on coil 1 instead of the timing loop to avoid weird issues with the timing light. Double check that your timing settings are actually correct, like is the 24 tooth configured correct or should it actually be 12 teeth for 1 crank revolution? I also found this: 305817248-AEM-Undocumented-Settings-v1-2.pdf    
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Yeah, I don't believe the M35 uses a deadhead system.
    • GTSBoy
      M35 Aftermarket Fuel Pump

      By GTSBoy · Posted

      Have you done your thinking backwards? 3 bar, 43.5 psi pressure drop being the presumed specification for an injector, means you need 3 bar upstream when they are firing into atmospheric pressure, and more upstream pressure than that when on boost (you add your boost to your rail pressure to maintain 3 bar across the injector) and you need..... less pressure upstream when you have vacuum in the manifold. So, presuming that you're idling at -10 psi, then you only need ~23 psi in the rail. I realise that I did not need to say all of that to you specifically Matt, once you'd realised your mistake. It's mostly there for complete clarity for others.
    • Dose Pipe Sutututu
      RB25 Drama's

      By Dose Pipe Sutututu · Posted

      Have you reached out to the guys at Spool Imports? They are a Ross dealer, I can imagine they would have the rings just sitting on the shelf (I could be wrong).  
×
×
  • Create New...