Jump to content
SAU Community

Recommended Posts

This car must sell as i work all around Australia and have no time for it anymore. there's not much mechanicly to do to finish off.... Parts include:

180sx RB20DET

Rollin Shell

Is in good condition some minor dings and scratches

Tein coil over suspension all round

600 x 300 x 100 intercooler with 3" inlet and outlet

5 stud conversion s14 up front with breaks

R32 rear hubs (no rotors)

Fuel System

Billet surge tank with bosch 044 fuel pump bracket

Skyline in tank fuel pump

Push on speed flow fittings for surge tank and pumps

Half inch fuel line from pumps to the front of the car

Braided speed flow from half inch to fuel rail

Modified fuel rail to twin feed

550cc injectors

SX fuel pressure regulator

Drive Line

R33 5 speed gearbox

OS Giken twin plate button clutch

Billet Fly wheel

All new gearbox bolts

R32 full spooled diff with 4:11????

Needs a one piece tail shaft (for strength)

There is a tail shaft 32 - s13

Modified gearbox cross member (new bolts)

Engine

Full house machine work

Polished, nitrided and cryoteched Crank

Cryoteched R32 conrods

CP 30 thou over pistons (brand new)

Over sized gudgen pins

Commetik steel head gasket

Total seal CP piston rings

Extreme head porting and polishing

Titanium valves, valve springs and valve seats

HKS stage 3 cam gears

HKS cam gear pullies

New oil pump housing modified for dry sump

New water pump

Polished rocker cover, crank angle sensor

Engine Cont'

Peterson stage 4 dry sump pump

Peterson dry sump tank 3L?

Stainless steel top mount turbo manifold

R32 GTR inlet plenum modified

Solid mounted engine mounts

XTR GT35R roller bearing turbo oil and water cooled

Electronics

Mircotech LT-12s computer with extra long cord for hand controller

Computer has about $1000 worth of tunning time with three tune settings

Pump fuel

Pump fuel + Toluline

C16 race fuel

Standard coil packs (have been rated at 800bhp)

Boost gauge

Air/Fuel ratio gauge

Turbo timer

NO time wasters this must sell asap $15000 or ONO

Please call me on 0401 419814 or Pete on 0404479491

post-52336-1213319123_thumb.jpg

post-52336-1213319149_thumb.jpg

post-52336-1213319183_thumb.jpg

post-52336-1213319214_thumb.jpg

post-52336-1213319285_thumb.jpg

post-52336-1213319331_thumb.jpg

post-52336-1213319364_thumb.jpg

post-52336-1213319385_thumb.jpg

post-52336-1213319406_thumb.jpg

post-52336-1213319428_thumb.jpg

Sorry mate im in Brissy not to much is needed BOV External Waste Gate.. Speed flow for dry sump and tank,2 x bosch 044 fuel pumps, exhaust and cooler pipes and tail shaft to get it running.... and will organise delivery if needed...

Edited by 23RIL

before i bought it and rebulit it, this build has previously made 584 rwhp on c16 tune which to my knowledge is still the highest HP for an RB20DET in australia... the injectors are a 550cc item.... This must sell and the price will drop untill sold......

Edited by 23RIL
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...