Jump to content
SAU Community

3 Front Drive Shafts In 2 Days- Gone

den001
 Share

Recommended Posts

den001 Proficient

den001

Posted
Posted

i had some problems lastnite bieng a dumbass and i popped a driveshaft, 32 gtr, drivers front, its come apart from the diff side...

now i bought 1 this morning, put it in, took for a good drive , no dramas, then going for another drive, goin around corner and gassed it abit in first, same same, again came apart diff side,

then put new one again, then also, gassed it in second, going in a atraight line...... and it popped aswell...

wtf??

the only thing i havent checked is the engine mounts, they feel good in the car, but if they were rooted, would this cause the motor to twist and lift causing the cv to spread open and come apart???????

ive ordered new nismo engine and box mounts, will this fix it...

Link to comment
https://www.sau.com.au/forums/topic/223880-3-front-drive-shafts-in-2-days-gone/
Share on other sites
  • 8 months later...
RipNGrip Collaborator

RipNGrip

Posted
Posted

I have a gts-4 r32 running rear wheel drive.. and after a little wear on the rear tires 4wd system kicked in and snapped the front right innner CV so i replaced it and the power steering line that it fractured and two/three weeks later while the 4wd system was deactivated; went over a big bump in my drive way and poped out the front right inner CV again... do u have any ideas on what could be causing it?

p.s my car is lowered with JIC coilovers but it isn't that low

  • 3 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • R34_GT to Turbo
      Does RB25DE Neo lower intake work with RB25DET Neo Upper intake manifold?

      By R34_GT to Turbo · Posted

      Ok I get you. But isn’t the butterfly intake a headache with the +T?  see this is my plan so far but please advise me into the right direction.  Nistune Ecu, 1000cc Bosch injectors, TD05 or TD06 Kinugawa turbo using stock rb25det exhuast manifold, walbro fuel pump unsure of model I think it’s 450/460, spitfire coils and sparks to suit and a R35 MAF sensor and boost sensor.    I was thinking maybe do a cheap eBay plenum $400-500 or try find a stock det neo intake. I think I’d port match it so it’s getting the full capacity but open to advice please.  Thanks 
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      The issue now is the 'fuel cut' while driving, and when it happend, it does not stall. This, I did not test the fuel pressure while driving as I cannot with a fuel pressure gauge. I do have Nistune logs, yes. I have also replaced the MAF Sensor.   Also related to the FPG Fuel Hanger – I just realized that I need a Deutsch Crimp Tool to crimp some cables for the FPG Fuel Hanger. Need to purchase additional cables as the kit only included 2, which are for the float. FPG has not responded to my emails so far since purchasing. I thought about taking it to someone and having it done professionally, but I am reluctant since everyone I took it to messed up in some way.  
    • MBS206
      NC MX5

      By MBS206 · Posted

      There's a good German place in Brisbane if youre up for the drive 😛
    • Dose Pipe Sutututu
      NC MX5

      By Dose Pipe Sutututu · Posted

      The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • joshuaho96
      R33 GTR running -9 with no tune

      By joshuaho96 · Posted

      Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
×
×
  • Create New...