Jump to content
SAU Community

Recommended Posts

made me cross over to the dark 2j side :)

pshh dark side my ass... nothing good ever comes from a 2j... what happened to all those fun times disassembling nissan motors after they start rattling and constantly fixing lil shit and getting no where.

that's where the shits at! never seen a toyota motor give its owner such wonderfull lengths of bonding time.

Edited by SkyHi_33
pshh dark side my ass... nothing good ever comes from a 2j... what happened to all those fun times disassembling nissan motors after they start rattling and constantly fixing lil shit and getting no where.

that's where the shits at! never seen a toyota motor give its owner such wonderfull lengths of bonding time.

plan is to crack 300rwkw on a stock bottom end...then push 400 which will result in plenty of bonding time :)

plan is to crack 300rwkw on a stock bottom end...then push 400 which will result in plenty of bonding time :)

haha it will take it... if an rb can take 300+ on a stock bottom end you should be perfectly fine.

and sice this is a photo thread, my new fav as of last night hehe

r331.jpg

haha it will take it... if an rb can take 300+ on a stock bottom end you should be perfectly fine.

and sice this is a photo thread, my new fav as of last night hehe

r331.jpg

Nice new guards! Whens the paint work gettin done ?

Oh and i ope it lasts...with what i have planned for it lol.

haha its getting rubbed down and primed end of next week before all jap day, gonna be in the show slammed as low as it will go. Getting painted sometime in March when I get around to it.

20022010112.jpg

this would be one of my favourite ones this week....

it means Marv is coming back out into the world after a 3 year 2 moth, 17 day and 11 hour lay-up in the shed...

woot woot!

  • 2 weeks later...
IMG_2301.jpg

IMG_2305.jpg

04.jpg

IMG_2689.jpg

just a few of my fav of mine...

but as she is now im not so proud, well doesnt look too hot as im in the middle of doing a few bits but here it is as she sits now :)

01-1.jpg

i know im not from south aus or anywhere in aus for that matter but i stayed there for 6 months a while back so though id throw them up :D

wow been a long time since i was on here, well above is how my car was before, think i better update it, seen as its slightly different now :D

firstly how she started out when i first got it.... :wallbash)

892643_20080117030150_1.jpg

:hmmm)

best get going at it then this is the lady today....

IMG_0432.jpg

IMG_0466.jpg

IMG_0445.jpg

IMG_0486.jpg

IMG_0473.jpg

IMG_0463.jpg

IMG_0420.jpg

let me know what you think then.

Because of the side skirts coming out as much as they do, I really think to finish it off stick a 10mm spacer behind the rear wheels and it will complete the whole overall look of the car :thumbsup:

^ that is very nice mate!

thanks

Because of the side skirts coming out as much as they do, I really think to finish it off stick a 10mm spacer behind the rear wheels and it will complete the whole overall look of the car :cheers:

thanks, yeah ive been thinking the same about the spacer, but i need a little arch work for the wheels to sit right as the standard arch was left when the 400r were put on, so they will rub like fook if i just stick a spacer on..... :thumbsup:

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Reading through the engine service manual their advice is do a cylinder balance test. Unplug one injector at a time and see if the idle drops a consistent RPM. You can also do this using a Consult cable which is easier. They also call for unplugging the power transistor, then with the engine off and the fuel rail unhooked from the manifold verifying that you have good fuel flow (even injection, no dripping/leaks, etc) when you twist the CAS by hand. Also verify the spark by pulling the spark plugs and allowing the plugs to ground and turning the CAS by hand. I would also start doing the sensor checks and idle valve checks in service manual. Make sure the MAF tests reasonably, the intake air regulator is sane, etc. You may have to get new spark plugs.
    • This sounds very old of me, however since buying the Tiguan shit box, my view on shit boxes have changed.
    • I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
    • This coupled with 6-9 speed autos with ridiculously short gearing is why these modern shitbox cars always seem so fast off the line. If it wasn't for those things, Raptors would not seem fast. The problem we have is there is a driveability gap between a more gentle take off and a wheelspinning sideways launch. The difference between ankle flex required to achieve one and ankle flex required to achieve the other is about 0.5°.
    • Yeah I think I'm also with the opposite here. It's 'hard to keep up with traffic' because in the real world I'm accelerating with 15% throttle and they are pinning it. It feels like I'm being an overt dickhead at anything above 15% throttle, so the car sounds like I'm being an overt dickhead to keep up with/get ahead of traffic when I'm really just trying to drive with traffic. There would be no issue 'keeping up with traffic' if we used the same level of throttle input/aggression to drive around. People really do just drive around with their foot nearly pinned in econoboxes.
×
×
  • Create New...