Jump to content
SAU Community

Recommended Posts

Hey everyone again

I need to know what you would choose between there 2 cars and why also if anyone has experience with either car what does it cost to run each week approx. A non turbo nissan silvia or a 1.8l 1997-onwards mitsubishi lancer. I cant decide which to get for my first car.

I like the silvia cause it has a bit of power and it sounds like a fun RWD 4cyl. Whereas the lancer i like cause i can whack on a EVO 7 or so body kit and make it look real good. Let me know what u think.

thanks in advance nathan

Link to comment
https://www.sau.com.au/forums/topic/22416-need-your-opinion-on-cars/
Share on other sites

Don't be fooled, the silvia is the go here, but it not your ONLY choice.

Maybe a late model 180sx non-turbo, they are a bit more expensive, but have the kick ass looks, with the non-turbo engine.

What about an AE86, they Kick ass and will appreciate in value.

Or if you want something on the cheap how about an old Celica, RWD, super cheap, heaps of parts and the oppertunity to do it up.

There are HEAPS more choices, all are more interesting than a lancer with a bodykit.

Greg.

Originally posted by Sonic

AE86 is a Toyota Sprinter. Like a shit-hot Corolla Seca. I think some had supercharged 1.6L 4A??? engines from the factory

The Supercharged 4A-G was introduced in the AW11 MR-2 in 1986, and the AE92 Levin/Trueno in 1987.

The AE86 had an NA 4A-G in Japan, but the Australian ones had a piss-poor 4A-C. Steer clear of the Ozzy ones unless you want to do an engine swap (if they havent had one already).

Originally posted by GTS-4OrCeD

Don't be fooled, the silvia is the go here, but it not your ONLY choice

What about an AE86, they Kick ass and will appreciate in value.

Greg.

Eh ?

They are so old the AE86 Sprinter/Trueno's....

There would be tons and tons of work to be done on them and good luck getting one for under $10,000 Imported and a decent version is fkn hard to find in Australia.

Go the lancer, it will look nice, put a fart can exhaust on it and a body kit you will have a nice looking car cruising around for mods less then $2000.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...