Jump to content
SAU Community

Recommended Posts

  • Replies 182
  • Created
  • Last Reply

Top Posters In This Topic

Yeah I ran at the creek, however even on the racing slicks we where running we had no traction through 1-3rd.. Thus running a very slow 17second pass. However with the new dual stage boost controller, we can run 3bar until we get traction and then run full boost. I rekon we will see some 9 second passes. I might need to get someone else to race the car for me, I dont think I could pilot it that quick.

Duncan might be in a position to help out there.

Once again unable to attend due to drinking/whoring commitments.......mates sisters 21st...mohahahahha ill be "bigging it up" benm stylz....enter the "hunter"......oh well....ill be out of action for awhile also moving into my apartment over next few w/ends so ill be flat out....next time...ey....seem to be saying that alot....pfft i wanna drive...

Ando

btw anyone know any decent dialup isp's? good connections and decent price??? Just need some form of connection till i can get adsl....damn to optus aloowed in apartments...GGGRRRRR

Ando

PS.....sorry for going of topic but hey it went from cruz details to mars bars to brotec..so i thought it would be fitting...lol




  • Similar Content

  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...