Jump to content
SAU Community

Recommended Posts

Hi unfortunately Just after finishing my project Not even being able to drive it 500kms before the unthinkable happened and my car was written off got hit in the Rear End by someone who obviously cant drive. The car owes me well over $50000 I have receipts for all the work and parts i have purchased for it most of the parts were bought directly from Japan. All top of the range japanese parts have been put on this car and the engine is still brand new not even 500kms like i said. I'm stripping everything from interior to motor to panels everything must go selling everything cheap and basically every part in brand new or hardly used. And as i said i have receipts for most of it.

Engine Parts include:

Fully bored and crack tested block with Arias Pistons and Rev conrods

The head has been ported and polished.

It has a Garrett GT3540r Turbo with .82 Exhaust housing with a Hi Mount Manifold which inludes

Oil and Water lines with a PSR wastegate plumbed back into custom V band dumpipe in Which JPC did a fantastic job of making it look factory. This Setup alone cost me in excess of $4000 with out labour All parts i have receipts for and done less that 500kms as my motor was still being run in so everything is in mint condition.

I have Denso 550cc Injectors with an Bosch 044 fuel pump and Sard Fuel Regulator.

Genuine Greddy plenum with Ford XF Throttle body including piping.

Os Giken Cam Gears Gates timing belt

Link Ecu with Hand Controller

2 Way Diff

Manual Gearbox with basically a brand new xtreme heavy duty clutch.

Bilstein Height and Damper adjustable coil overs

black Chrome 18 inch Rims with good tread

Everything i Have put alot into this car and has been modified to make big power was looking at making at least 360rwkw was making 330rwkw on my old setup before motor was built and new turbo etc was put on.

These are just the parts i can think about on top of my head there is plenty more.

I also have a Trust Front bar and nice trust sideskirts clear indicators

The interior is A1 and series 2 i need everything gone.

Going to take motor out this weekend and gearbox etc.

Will post up prices in the next couple of days if anyone needs any parts just let me know and i will take it off for you. I have lost an absolute fortune on this car and whats my loss is your gain just need it all gone makes me to depressed looking at it knowing how much i have put into it.

cheers

Edited by wildr33gtst
Link to comment
https://www.sau.com.au/forums/topic/225450-wrecking-fully-worked-r33-gtst/
Share on other sites

  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

will put up some prices when i go home im located in bentleigh. Will be home in an couple of hours 2 reply 2 everyones messages and posts. Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Well, this is probably where a wiring diagram and a multimeter come into play.
    • I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...