Jump to content
SAU Community

Removing Stuck Clutch Lines?

eXc

By eXc,
in General Maintenance

 Share

Recommended Posts

Beer Baron Grand Master

Beer Baron

Posted
Posted

what you will probably need is a pipe spanner. it's like a normal ring spanner but with a slot in it so you can slide it over the pipe. if need be extend it by hooking another spanner or a small piece of pipe to it.

**RB2530** Proficient

**RB2530**

Posted
Posted

Keep trying the WD40...Spray and leave it for 20mins then spray again and leave and so on...

I have also seen some freezing spray at Repco..never tried it but give it a go...Only spray the nut though...dont spray the whole thing otherwise you defeat the purpose of freezing it..

Godzilla32 Veteran

Godzilla32

Posted
Posted (edited)

We have that freeze stuff at work. Im not sure how much it actually helps. Just keep up the WD-40. One reason it may be hard to undo is if the whole pipe is moving around while your trying to crack the flare nut that will be absorbing alot of the effort so trying to brace it from moving with another tool without damaging the pipe might help you to crack the nut. If there is flats on the other connection you are undoing it out of use another spanner on them and position the 2 spanners so they are not too far from each other and then with your hands just squeeze them both together. That technique is very useful :rofl: Hard to explain on here though. Or as mentioned use a decent pipe spanner and then either another one locked into the other end of it or a metal tube over the end of it and give it a sharp hit with the palm of your hand and it should crack it.

Good luck mate,

Deren

Edited by Godzilla32

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • drifter17a
      Rb25 trigger kit and timing misalignment

      By drifter17a · Posted

      Hey all,   I’ve got an RB25 with a trigger kit that includes a crank wheel, and I’ve hit a wall trying to sort a timing belt tracking issue. The belt either rides right on the edge of the cam/crank pulleys or walks slightly forward once the engine starts. It tracks okay-ish for a moment, then creeps right to the edge—and honestly, it’s stressing me out.   I’ve spent hours removing and reinstalling the belt, double-checking everything:   Tensioner setup is good, checked multiple times Idler pulley and washers are all in the correct places Followed the RB25 timing procedure step-by-step     The only thing I changed was the rear crank washer—I swapped the OEM one for a Neato version, and it made things worse. The belt now sits even more forward than before. I’m beginning to think the crank trigger wheel itself (from the trigger kit) is the issue—poor design or slightly off dimensions.   What’s strange is that with the previous belt setup, it actually ran fine for a couple of years—around 4,000 to 5,000 miles, even with hard driving and high RPMs. But even then, the belt was always riding right on the edge, and I know that’s not ideal or safe long term.   At this point, I’m debating whether to:   Machine a few mm off the crank trigger wheel to bring it back in line, or Replace it entirely with a better-designed unit     Only thing is, I already have the Cherry Hall sensors, bracket, etc.—I just want to replace the wheel only, not the entire kit. Anyone know a brand or supplier that sells just the crank trigger wheel on its own?   Would really appreciate any feedback—especially from anyone who’s run into this exact issue and found a reliable fix.   Thanks in advance.
    • Kapr
      Question about BoV on RB25DET NEO

      By Kapr · Posted

      Hi...a little refresh. Is Nistune gonna be enough to run BoV? Or do i need some proper ECU? 
    • Ozdavroz
      ATCC Amaroo Park 1987

      By Ozdavroz · Posted

      Yep that's pretty much what I want to see. Racecars that look and sound like the Group A but with newer tech underneath to make them faster and safer. I'm sure there's enough VK-to-VN commodore, E30 BMWs and Foxbody mustangs shells around to make up a decent number of cars with hopefully a couple of sierras, rx7 and R31s in there too. 
    • robbo_rb180
      WTB RB25 Gearbox NSW / central west

      By robbo_rb180 · Posted

      Contact Jessestreeter.com/Skevas Racing/JustJap for a new r34 rb gearbox or go a cd00# conversion. No point playing with unknown condition gearboxes.
    • robbo_rb180
      ATCC Amaroo Park 1987

      By robbo_rb180 · Posted

      Such a shame places like Amaroo Park have been redeveloped, smaller tracks always make for good racing. Cheers for sharing @PranK there's some good Lakeside video's too. Its so hard with older the cars as parts are so rare and everything was made for a particular chassis at that point in time. Even the V8 Supercar Blueprint era cars are all different between each chassis within a team as they learnt things and made improvements. The COTF cars between each Chassis builder is different too especially motor/oil systems/intakes. The Group A stuff is worth so much too especially chassis with good history. The only way to do it would be composite panels and similar engine drivelines to the original cars. Ford sierra running Focus RS driveline, Commodore running a short stroke LS/LT or a Falcon with coyote and a H Pattern dog box. Could use a standard ecu across all models with a Torque Map and DBW for parity which is not even used in Supercars currently. Hell a TCM is almost a full chassis car these days and the suspension is not even close to standard style in the front running cars.  
×
×
  • Create New...