Jump to content
SAU Community

Recommended Posts

I have a question to the ether.

I am having a problem with the HICAS warning lamp coming on after around 15mins of driving.

It happens whether I cane it or not, and it has me a bit stumped.

Because it seems to be an event that happens after a given amount of time...it could be temperature related.

Other than that I have checked power steering lines for leaks and have not found any.

If anyone else has been through this traumatic experience and finally came to an answer I would appreciate the heads up.

R32 91 GTSt - pretty stock (no engine mods - only suspension and brake rotors)

Link to comment
https://www.sau.com.au/forums/topic/22760-hicas-light-problems/
Share on other sites

hey dude sorry i have no answer.. but i have the problem too i have a 1993 180sx and the same thing happens i start my car ans let it warm up for about 5 min and then the hicas light comes on..plus some times my turbo timer poo's itself too so i let it warm um then before im about to drive off i turn my car on let it sit for about 30 seconds the start it up again my hicas light stays off and sometimes my turbo timer works properly too... hmm got me stumped too .. if anyone can help it would be mighty sweet of ya's ..

Guest xbellx

I have had a heart wrenching experience with Hicas lights. I finally solved the problem of the light coming on after five minutes of driving. It involved setting up the two sensors on the unit as follows. There is an input sensor & an output sensor, they look almost like a throttle positon sensor. the three wires are 5v positive, negative & output voltage. The out put voltages of both sensors must be identical, this is the key to the light not coming on. You must set it up with a multimeter on the output voltages of both sensors. adjust both sensors at the same voltage. They can go out of adjustment when drifitng & hitting gutters.

xbellx

Very interesting...I would be very keen to hear more about how this is acheived. If you have any photo, more detail please feel free to private message (pm) me, or even post it on this forum.

I appreciate your input...and I'm glad there are other Skyline drivers out there that have felt my pain.

  • 4 months later...

Just a quick note; After fitting a momo wheel and after market boss kit my hicas light would illuminate after driving in a straight line for 10 or so minutes, after further inspection i found that the boss kit was different to the standard wheel in that the hicas sensor had too much room to move within the boss kit. to remedy the fault i wrapped the hicas sensor's prong with some adhesive foam and then some race tape to keep it neat while the boss was re fitted. now the sensor sits perfectly central with the gap taken up with the foam. Hope this has been of some assistance and MERRY CHRISTMAS HO HO HO............ now to wrap more presents! :D

Yea I have the same problem as AutoTrust. Might try that little wrapping trick...haven't really been bothered with it coming on, but if anyone else drives the car on the highway for instance, it freaks em out.

Mildman, don't worry...you're not the only one with a HICAS problem! that's why we're all here :D

Hi Guys,

I have fixed my problem on mine it was the standard wheel or maybe it wasnt standard.

With the original the hicas sensor on the column was sitting about 30 degrees left, when i brought a boss kit and aftermarket wheel it sat top center.

This has fixed my problem no more hicas light coming on.

Hopefully this is the same problem some of you are having because it was simple to fix.

Dan

I fixed my 'HICAS twitch' by cleaning the battery terminals and re crimping the wires of the main harness leading to the battery. I found that a power fluctuation will cause the car to twitch sideways when the HICAS light comes on. Most of the cables leading to the battery had loose connectors. After tightening everything the 'twitch' went away. However the HICAS light still comes on.

I'll try the wrap procedure next.

Still would like to know how to do that sensor adjustment though.

can the self steering be fixed by disconnecting the battery again with the steering wheel straight?

Yes It Will fix that problem, you would have to turn your lights on and / or press the brake pedal to drain all power from the car, same as you do to reset the ECU. :)

I just got a new wheel & boss kit from santa yesterday and fitted it. I installed it yesterday but my wheel isnt at dead centre, i think its about 1 knotch out, and the HICAS light comes on after about 10-15mins of driving. Something to do tomorrow i guess, is re-align the wheel, and hope that the light doesnt come back on....

the boss kit is a HKB one, and i hope that it is the right one....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...