Jump to content
SAU Community

Recommended Posts

Thanks for reiterating that. Certainly safety is the foremost important aspect of any sport. I have no problem with the safety requirements at all.

However, how does enthusiasts like me benefit from paying the full UDL? What does the personal protection cover? Why is this cover higher than the guys, with superstreet licence, that don't have as much personal protective equipment or safety equipment in their slower vehicle? As you rightly said they can still roll their cars and kill themselves at lower speed too...if they don't have the full roll cage.

They are all questions to ask the person you are buying the goods/service from.

Not a bunch of filthy ricers on a forum :(

  • Replies 68
  • Created
  • Last Reply

Top Posters In This Topic

Think of it as like an insurance premium. when your in a higher risk catagory, you pay more. i think the idea is if i have to pay X amount a year, make good use of the liscense.

there are plenty of events to race.

Thanks for reiterating that. Certainly safety is the foremost important aspect of any sport. I have no problem with the safety requirements at all.

However, how does enthusiasts like me benefit from paying the full UDL? What does the personal protection cover? Why is this cover higher than the guys, with superstreet licence, that don't have as much personal protective equipment or safety equipment in their slower vehicle? As you rightly said they can still roll their cars and kill themselves at lower speed too...if they don't have the full roll cage.

Edited by BezerkR32

im glad ive got all the safety gear...when you have a young family and drive as bad as me you need it...its the expensive licence that eats me...im not a hard core drag racer and only attend the occasional meeting so its a big expense when you put it in that light. Maybe have a user pays system where the licence is X amount then a run fee is paid at each event as you register that ANDRA collects. Why should casual racers pay into a development fund to televise a meeting that they are not even attending. That way the casual racer with a quick car is not so out of pocket.

Edited by DiRTgarage

i find it weird that circuit racers want to drag race, isnt that funny.

As a percentage of your total costs I doubt it is a large amount - maybe for other part time racers, but not yourself Paul.
Think of it as like an insurance premium. when your in a higher risk catagory, you pay more. i think the idea is if i have to pay X amount a year, make good use of the liscense.

there are plenty of events to race.

exactly.

i do agree licenses for UDL are pretty hefty now with the DRDF added on, and its going to get worse once i start racing group 2 ozmod, i hope that the increased television coverage helps get more sponsors, time will tell.

at the end of the day if this is a sport you want to compete in at these tracks you have to pay the money or go race at heathcote. by the time you towe a car there an back from NSW theres the money for your UDL and you get a better track

exactly.

i do agree licenses for UDL are pretty hefty now with the DRDF added on, and its going to get worse once i start racing group 2 ozmod, i hope that the increased television coverage helps get more sponsors, time will tell.

at the end of the day if this is a sport you want to compete in at these tracks you have to pay the money or go race at heathcote. by the time you towe a car there an back from NSW theres the money for your UDL and you get a better track

Finally putting on that 1st grade jersey thats had your name on it for so long.

good to hear Shane and good luck with it.

Pffft... It's still the reserves. There's a ban waiting for him when he buys a Supra, too!

:)

Its 1st grade in a full bodied car.

What? a supra! does dad want his car back?

I can just visualise "dad, can i borrow the car" dad replies "well ok but how long are you going to be?" shane replies "9 seconds" lol

Edited by DiRTgarage
Its 1st grade in a full bodied car.

What? a supra! does dad want his car back?

I can just visualise "dad, can i borrow the car" dad replies "well ok but how long are you going to be?" shane replies "9 seconds" lol

im waiting to see what ray does next year before i commit to cutting 900 pounds of weight out of it.

still want to go mid 8's on the radial yet.

Bzzzzzzt!

Pro Hairdresser (PS), Top Wallslammer (TD), Pro 2J20B (PR) is Grp 1.

all i ever wanted was a 9...now i want an 8...where does it stop?

sorry 1wristmo mistake by me...deduct 5 points :)

ANDRA have other considerations besides late model cars and their inherent safety systems. Go to any tnt or race meeting and you will see a very high percentage of not so new cars running some damn quick times even by todays standards.

Old torana's, Falcon.s valiant's etc abound at the strip And most skylines arent excactly newish either.

While most of them are well prepared there is no getting over the fact that they are old. Anything can and does go wrong at the drags and I commend them for their stand.

Think of it as like an insurance premium. when your in a higher risk catagory, you pay more. i think the idea is if i have to pay X amount a year, make good use of the liscense.

there are plenty of events to race.

Yes but the total risk is the product of relative risk and exposure. Infrequent exposure (drag race) in a medium risk category still should be considered as low risk.

I am thinking the same line as dirtgarage as well. Why cant we have a "PAYGO" system. It certainly will attract a lot more enthusiasts and should improve Andra revenue.

It's not rocket science, just a basic supply and demand curve.

They are all questions to ask the person you are buying the goods/service from.

Not a bunch of filthy ricers on a forum :thumbsup:

Nah it's more fun to get people different opinions on here.

If I call up Andra, I will get a very straight Nazi answer.....pay to play mate.

Or may be I should enlighten them with a brief supply and demand economic lesson as well.....I doubt that will change anything though :thumbsup:

Insurance, safety gear, clothing, development funds etc etc are all valid points for having licensing, no sensible person would question that. What it is valid to question is the accuracy of the demarcation lines and whether or not they are up to date. For example, at some point in time someone decided that an 11.00 ET was a line drawn in the sand that said once you cross that line you have to do certain extra things.

The real question here is how was the 11.00 decided? If it was based on the logic that no production cars do 10.99, then it’s time to question that logic. The idea that all cars running faster than 11.00 couldn’t possibly be “road cars”, hence they must be “race cars”. Since they are “race cars”, their owners should have no problem with cages and other items that further separate their “race car” from a “road car”. To achieve that sort of time their owners will have carried out a large number of modifications. Such modifications that have taken the car so far away from being a “road car” that the owner couldn’t/wouldn’t/shouldn’t validly complain about a few more safety related requirements.

The problem currently being faced is that there are an ever increasing number of production cars that, with a minimum of mods, can easily exceed the line in the sand. These are “road cars” in my definition and hence why the line in the sand should be reviewed regularly. Otherwise we are risking turning their owners away from doing their racing where it belongs, on the track. After all that’s what we are really talking about here, why the government kicked the can to build the track in the first place. Give the guys with “road cars” somewhere to race other than the streets. If the current ANDRA regulations are turning these guys away, then it’s time to review those lines in the sand.

Cheers

Gary

Nah it's more fun to get people different opinions on here.

If I call up Andra, I will get a very straight Nazi answer.....pay to play mate.

Or may be I should enlighten them with a brief supply and demand economic lesson as well.....I doubt that will change anything though :thumbsup:

The questions you posed are all one answer questions#. I am sure there is a list of things you are covered for, but you seem to see ANDRA as the enemy with your reference to Nazi's. How about you actually attempt to contact them instead of knocking them? Going off your above post you haven't even done so.

how does enthusiasts like me benefit from paying the full UDL?

#Well all barring this one which is really a matter of opinion, as the "value" of any thing always is.

Insurance, safety gear, clothing, development funds etc etc are all valid points for having licensing, no sensible person would question that. What it is valid to question is the accuracy of the demarcation lines and whether or not they are up to date. For example, at some point in time someone decided that an 11.00 ET was a line drawn in the sand that said once you cross that line you have to do certain extra things.

The real question here is how was the 11.00 decided? If it was based on the logic that no production cars do 10.99, then it’s time to question that logic. The idea that all cars running faster than 11.00 couldn’t possibly be “road cars”, hence they must be “race cars”. Since they are “race cars”, their owners should have no problem with cages and other items that further separate their “race car” from a “road car”. To achieve that sort of time their owners will have carried out a large number of modifications. Such modifications that have taken the car so far away from being a “road car” that the owner couldn’t/wouldn’t/shouldn’t validly complain about a few more safety related requirements.

The problem currently being faced is that there are an ever increasing number of production cars that, with a minimum of mods, can easily exceed the line in the sand. These are “road cars” in my definition and hence why the line in the sand should be reviewed regularly. Otherwise we are risking turning their owners away from doing their racing where it belongs, on the track. After all that’s what we are really talking about here, why the government kicked the can to build the track in the first place. Give the guys with “road cars” somewhere to race other than the streets. If the current ANDRA regulations are turning these guys away, then it’s time to review those lines in the sand.

Cheers

Gary

Again I disagree. Also, your speculation about how they came to the decision of 11 being the limit for a licence acheives nothing.

In all reality lets look at this from a common sense perspective.

To run 10's you need to be doing what? 120+mph? (my rough guess - happy to be changed)

At around 200km/h I would (as I would also hope any other sane person would) want to be as safe as possible, therefore racing at the safest possible track - new car or old. Additionally, one would assume that some form of personal protection cover would be offered.

I think it is more than reasonable to be paying whatever is required to get the highest quality of safety along with all the other benifits outlined previously.

Can any of you put a value on your life? If any of you suggest lower than what it costs to get a licence + build a racecar............I feel for your family.

the line in the sand has to be somewhere, and thats were it is. i cant see it changing, 11.00 is damn quick by anyones standards.

the days of having a street car that runs low 11's or tens is long gooone. you simply cant have those cars without being defectable.

the line has been drawn in the sand and people have to live with it, accept it and pay for it, or dont race. simple

if we keep lowering the standards, next we will see big victor in his 57 running a 5 in a t shirt & double pluggers sipping a rum and coke.

aint going to happen

the line in the sand has to be somewhere, and thats were it is. i cant see it changing, 11.00 is damn quick by anyones standards.

if we keep lowering the standards, next we will see big victor in his 57 running a 5 in a t shirt & double pluggers sipping a rum and coke.

aint going to happen

What a horrible farking image! I'm off to wash my brain out!@@@!@!!@#!#$!@#$@#!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Any update on this one? did you manage to get it fixed?    i'm having the same issue with my r34 and i believe its to do with the smart entry (keyless) control module but cant be sure without forking out to get a replacement  
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if something was binding the shaft from rotating properly. I got absolutely no voltage reading out of the sensor no matter how fast I turned the shaft. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if shttps://imgur.com/6TQCG3xomething was binding the shaft from rotating properly. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
×
×
  • Create New...