Jump to content
SAU Community

Recommended Posts

  • Replies 59
  • Created
  • Last Reply

Top Posters In This Topic

if you could get a quote for a s/s version to suit a r34 (would have it in a simular location to where yours is), with the speedflow fittings i would be keen. I believe you that there hasnt been any problems, i'd just rather have peice of mind when i'm booting the shit out of it, knowing that there is no way main oil lines will be leaking/popping off.

Also, could the thermostat be intergrated into the s/s line?

:(

yeah the thermostat can still be used, just means another 4 fittings.

fair enough for wanting peace of mind, it just costs a bit more

im going to have a sus on exact pricing on monday.

how much for just the oil cooler core only ?

pm sent

would this fit a 7mgte / 7mge (from ma70 supra) also interested in speedflow fittings

yeah, it definitely fits the block.

NOW for the few people who are interested in the braided line version with speedflow fittings (blue and red anodised alloy) it will cost another 150-170 on top of each kit price. (not including the thermostat.) That is IF there are a few people who are interested in the kit with the braided line and fittings.

The braided hose itself is actually of a larger diameter also which means less restriction on the system.

So we're looking at around $550-$570 including the braided lines, speedflow fittings and thermostat?

I may be interested. Need to measure if the core will fit in the front of my Stagea somewhere.

I'm interested in an oil cooler with thermostat and speedflow fittings.

+1 definately interested in the whole lot

how many people did you need for the braided version to go ahead?

So we're looking at around $550-$570 including the braided lines, speedflow fittings and thermostat?

I may be interested. Need to measure if the core will fit in the front of my Stagea somewhere.

incorrect. another 4 fittings and 4 adapters are needed for the thermostat.

the kit will be 2nd to none though, with every component being the best you can get.

I'm interested in an oil cooler with thermostat and speedflow fittings.

interested as in deposit interested?

+1 definately interested in the whole lot

how many people did you need for the braided version to go ahead?

3 deposits of say $80 will get it rolling. 1/2 week turnover.

this whole kit needs to be revised if there is CERTAINTY for the braided version with necessary fittings.

the first quote was for 3.5M of braided hose.

if you measure how much hose you require in TOTAL i can adjust kits to suit.

PLEASE DISCUSS, because the fine details are important.

I'm looking at mounting the oil cooler where the SMIC is. (Will be changed to FMIC of course) So if you could allow for that length. 3.5m should cover it I would think.

this whole kit needs to be revised if there is CERTAINTY for the braided version with necessary fittings.

the first quote was for 3.5M of braided hose.

if you measure how much hose you require in TOTAL i can adjust kits to suit.

PLEASE DISCUSS, because the fine details are important.

if you copied a simular length to what you have in your car, but just in braided line and the provision for the thermostat that should work well. Most people would have it in a simular location to where yours is.

You can definately add me as apart of the group of 3, as soon as 2 other people show interest in the same kit i dont mind putting $80 deposit

:P

if you copied a simular length to what you have in your car, but just in braided line and the provision for the thermostat that should work well. Most people would have it in a simular location to where yours is.

You can definately add me as apart of the group of 3, as soon as 2 other people show interest in the same kit i dont mind putting $80 deposit

:P

I'm sweet for a deposit too.

Hey mate,

Interetsed, but can you please confirm price for full kit, with braided lines long enough to mount on the passenger side of a 32GTR?

Whats the actual size of the core, (Dimensions)

is there any chance of buying the speedflow fittings and ss braided hose by itself?

i'm quite keen as i have a similar setup using the permacool and b&m thermostat with a sertrab core

i'm yet to be install the kit on the car,

and i have always been a little concerned about the rubber hose that is supplied kinking and then restricting the oil flow...

pm me if possible,

thanks,

greg-

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...