Jump to content
SAU Community

Engine Light? Need Help!

THR34T

By THR34T,
in Engines & Forced Induction

 Share

Recommended Posts

THR34T Mentor

THR34T

Posted
Posted

I never seen this light come on before in my car. ive been told its something to do with the engine. does anyone know the possible causes for the light turning on? what is it indicating i am not sure. i recently had the car major serviced with new timing belt etc. Can anyone tell me possible things that could be wrong to make the light come on and who should look at it to help define the problem?

any advice would be good thanks

post-45807-1217321858_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/230131-engine-light-need-help/
Share on other sites
G0DZLR Mentor

G0DZLR

Posted
Posted
I never seen this light come on before in my car. ive been told its something to do with the engine. does anyone know the possible causes for the light turning on? what is it indicating i am not sure. i recently had the car major serviced with new timing belt etc. Can anyone tell me possible things that could be wrong to make the light come on and who should look at it to help define the problem?

any advice would be good thanks

get a not-so-blurry photo so we can make out the icon, unless you can describe to us what it looks like otherwise

116.hks Community Regular

116.hks

Posted
Posted

someone has probably left a sensor unplugged or there is a sensor playing up and it has logged a code in the ecu. u need to contact an auto elec or if u have a tuner that has a scan tool to check what code it has logged. it usually takes 3 times for the problem to log a code before the code is logged in the computer. have u notice if the car has lost power or hard to start or doesn't idle well etc. hope this helps.

THR34T Mentor

THR34T

Posted
  • Author
Posted (edited)

cheers for advice..its NA so no boost controller :) lol... yeah im getting it checked monday i did find a link on forums bout this problem it might be. ive been told it could be coilpacks or sensor problem but i will find out at my mates garage. clearer picture is attached..

cheers for the advice! ive been guessing it would be coilpacks but i been told aswell that the light coming on has nothing to do with the coilpacks so getting confused with all the different advice.

post-45807-1217402893_thumb.jpg

Edited by b3za
MissR34 Grand Master

MissR34

Posted
Posted

errr.....when my coilpacks went...one at a time....three times before i ended up getting splitfires.........the engine light came on.......just be careful of "ghost"error coeds when plugging in the ecu to a laptop....sometimes the real problem dosent come up and something else will.... e.g mine came up with crank angle sensor malfunction lots of times when it was a colilpack!

THR34T Mentor

THR34T

Posted
  • Author
Posted

alright well thanks alotfor the advice! i think im convinced to change coilpacks after monday unless something else comes up which i havent heard before but defaintly kept in my mind. i did suggest to my mechanic mate that it most probably is the coilpacks but i shall let you guys know on monday what comes up.

thanks again

AlexR34 Proficient

AlexR34

Posted
Posted
alright well thanks alotfor the advice! i think im convinced to change coilpacks after monday unless something else comes up which i havent heard before but defaintly kept in my mind. i did suggest to my mechanic mate that it most probably is the coilpacks but i shall let you guys know on monday what comes up.

thanks again

Lol i remember when i was posting the same question recently. Most of the time that light comes when the coil packs are gone. Also before blowing money on the coil packs check that its not the oxygen sensor because when that goes, you get the same light aswell.

Theres a way to get the error code from your car just using a paper clip. Im sure someone on here can give you the manual on how to do it. Its super simple and super useful.

MissR34 Grand Master

MissR34

Posted
Posted (edited)

when my car was losing a coilpack - it would lose a cylinder and then gain it back - everytime it lost a cylinder the engine light came on, and when it gained the cylinder back the engine light would go off (weird huh!!)

anyways i dont think it is a waste of money to go and buy some Splitfires - i gained 7 kW@ :( and in the end the stock coilpacks are gonna die anyway - mainly due to heat and age....in my opinion if i knew that when my first coilpack went i would have gone and replaced them then, instead of going and spending $200 on each coilpack i had to replace (which ended up being three of the buggers)

best thing is to do also is to get it on a dyno and that will tell u if ur o2 sensor has died.

Edited by MissR34
666DAN Grand Master

666DAN

Posted
Posted

Paper clips at the ready!!!!!

As the document says, turns the ignition to "on" short the two terminals indicated on the consult plug (clipped covertly on the underside of the dash near where your right knee lives), count the flashes, look up the code

diagnostic.doc

Im_RiCK_JaMeS_BiArTcH Enthusiast

Im_RiCK_JaMeS_BiArTcH

Posted
Posted (edited)

Mine was doing similar last night but i have already had coil packs replaced not long ago. The engine light will come on under load in 5th gear but it will only flash for a second.. only any one got any clues?

Edited by Im_RiCK_JaMeS_BiArTcH

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...