Jump to content
SAU Community

Recommended Posts

  • Replies 59
  • Created
  • Last Reply

Top Posters In This Topic

still got

box, gauges, turbo, and mirrors

also got a front facing R33 RB25 plenum (custom top section bolted to stock runners with RB25 TB) $550 ono

bump

g/box can still be used in a GTR if someone has a transfer case

price will also be cheaper if its bought without my 2WD transfer case

g/box sold pending payment

still available

genuine ganador carbon mirrors $300

defi BF gauges (oil temp,boost,water temp. fuel press.)

with sensors and controller $800

front facing RB25DET plenum $500

thinking of selling my RB30 bottom end

rebuilt CP forgies, stock rods and acl bearings

just completed the run in before it was all stripped

if anyone's interested PM me

coilovers and RB30 still here

also got

Pivot Speedmeter X - $90 delivered

• LED Speed Readout (0-350km/h)

• Speed Limiter Cut for Japanese Vehicles

• Interchangable Between Cars

• Peak Hold km/h Readout

• Automatically Records Time to Distance (0-100, 200, 300 & 400m)

Automatic measuring system allows you to track acceleration speed by setting desired distance and get readings for time and max speed over that distance.

This unit also removes the speed limiter built into Japanese domestic cars to stop them from going over 180 km/h (K cars -140 km/h).

With this unit you can experience the world of high speed over 180km/h.

sml_x_06.jpg

Pivot Shift light - $70 delivered

ssl_x_06.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...