Jump to content
SAU Community

DIY R32 cooler install

JH32

By JH32,
in Engines & Forced Induction

 Share

Recommended Posts

JH32 Grand Master

JH32

Posted
Posted

This is for anyone who has an R32 and is thinking of paying someone to fit their cooler.

After getting quotes of around $650 to fit my intercooler, I decided that the money was better spent on beer, so my brother and I went to work fitting the thing :)

It was actually surprisingly easy, and let me be the first to admit that my mechanical skills aren't that flash. I pulled the front bar off, removed all the stock cooler components including supports, pipes etc but left the pipes that are in the engine bay.

I then had to cut a few parts of the metal supports to fit the cooler and piping in, but nothing major. Luckily for me, it appears that my car probably had a front mount in Japan so the big hole in the support bar at the front had already been done.

I then drilled 2 holes in the support bar and bolted the cooler to that. The piping then went out of the cooler on the drivers side and back underneath, running along the length of the front of the car to meet up with the stock piping.

It took about a day in total but now my car feels HEAPS better!! I'm going to put it on the dyno and get the timing and boost set properly and then take it to the drags :(

Anyway I thought I'd write this in case other people were going to be lazy and get someone to fit their cooler for them! Don't be lazy fit it yourself it's not that hard!! Instead of paying $650 it cost me about $180 for all the parts.

You've also gotta have a few brews to hand when undertaking such an operation :) :alcoholic

;)

oh here's a pic of how we did it

409james_bar.JPG

Link to comment
https://www.sau.com.au/forums/topic/23142-diy-r32-cooler-install/
Share on other sites
MM2death Grand Master

MM2death

Posted
Posted

JiMiH, i am almost ready to do my own FMIC installation.....my 600x300x76 Hybrid is sitting in my room......anyhow, was it easy to route the piping back to the standard pipes? Will that 180 bend on the drivers side affect velocity? What material did you use for the piping.... I think i'm going to use grade 304 stainless. What size is your cooler?

Your install job looks neato btw...

Regards,

Scott

JH32 Grand Master

JH32

Posted
  • Author
Posted

Scott,

it was pretty easy to route the piping back to the original pipes. You've just gotta be careful with your measuring. For the 180deg bend I bought a donut and then cut it in half. This way you get the tightest bend. I had to angle it downwards so it would fit behind the cooler, and in front of the radiator. It also has to go slightly below that fan on front of the radiator. I'm not sure what effect the 180deg bend has, but it doesn't seem to be any laggier than stock so I assume it hasn't had any negative effects :D

My cooler is exactly the same as yours, just not branded a Hybrid. Same dimensions etc also.

The bits I bought were :

1 x 2.5" donut

2 x 90deg 2.5" mandrel bends

2 x 3" ---> 2.5" pipe reducer

2m of 2.5" piping

yeah I mounted mine to the bar above the cooler ... not sure if it's strong enough but the piping holds it, and the whole things as tight as a nun's snatch :P but i'm also get some brackets welded to the underside soon to give it some extra strength.

Hope that helps some :)

Mr R32 M-Spec Experienced

Mr R32 M-Spec

Posted
Posted

I was in the same boat, even though I had purchased the HKS Kit for the R32 GTST, I have no technical skills at all. got a mate who knows what he is doing and we knocked it over on a saturday arvo. cut 1 hole and it looks sweet as. HKS kit fits with no modification bar that 1 hole we had to cut, although I should mention there was already a dotted line in the chasie where a pipe should go... guess the GTR's and GTS's share a few similarities

didn't have to cut the support bar or bumper though, fit straight on. cost me $1300.00 delivered to me. we cut out the front bumper and put mesh in it though, for more of a sporty look :D:D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
×
×
  • Create New...