Jump to content
SAU Community

Recommended Posts

After rebuilding my RB26 with the following specs I have spun a bearing on no 2 after 2000kms. All of the other bearings are also hammered - and I believe it may be due to a clearance issue.

Here are the specs:

Aries Pistons and rings (86.5mm)

std rods with ARP bolts

ACL Race series bearings

STD oil pump (start the flaming....) oil pressure = 20psi hot at idle up to 80psi odd at high revs (ie good oil pressure)

Trust baffled sump (insert type, not weld on)

Castrol 10W60 edge syn oil

2xoil coolers

external filter block

Tomei head oil restrictor

The engine ran strongly and made good power (high 300rwkws), the knock recorded (pwr fc) was always <35, AFR always logged and spot on via laptop and wideband.

They should be the related specs required - please ask if you require more info.

My engine was built with around 2.5 thou clearance on the rod bearings, although the factory spec as per the manual is 0.8 - 1.5 thou. I am wondering if the greater clearance of 2.5 thou has killed the bearings and what clearances people are using in similar built motors of the same horsepower.

I am looking for ideas from people with EXPERIENCE / and or ENGINE BUILDERS of 400rwkw RB26 engines here - please don't post if you don't know what you are on about!!

Any help is greatly appreciated, I really don't want this to happen again!!!!

Cheers,

Andrew

Blue32

Link to comment
https://www.sau.com.au/forums/topic/232242-rb26-rod-bearing-clearances/
Share on other sites

Mines no fire breather, but my big ends were set around 1-1.5 thou and the mains I set at 1 thou. I was bit worried that the mains could have been tight, but it was with in spec. I have since completed 30,000km plus.

My Vl turbo done some 100,000km and I set the mains closer to 2 thou and the mains similar I think.....

My first imression was that 2.5 thou sounds rather loose for an RB engine. Remember that NIZPRO run what are considered to be tight clearences, like 1-1.5 for both mains and big ends...

Other than contaminated oil (or surge), detonation and clearence issues bearings are generally issue free.

I totally sympathsize with you.

Andrew, you are fairly fast at Mallala and your engine failed at the track. Have you consider other causes especially oil surge with your setup?

What oil pump and oil cooler have you been using? What was your oil temperature when the engine failed?

With the amount of g force you are doing around Mallalla, the Trust baffle insert may not be enough if you have a high flow pump. I think a Trust sump extension kit will help your oil surge

Edited by 9krpm

i run 2 thou on a 420rwkw rb26, has made over 450rwkw on dyno and no dramas with bearings. Im using acl race series if that matters. Has been running for 8 months with no problems. I got this clearance reccomended to me by a well known rb26 specialist workshop so i trust them 100%

Edited by unique1
i run 2 thou on a 420rwkw rb26, has made over 450rwkw on dyno and no dramas with bearings. Im using acl race series if that matters. Has been running for 8 months with no problems. I got this clearance reccomended to me by a well known rb26 specialist workshop so i trust them 100%

What oil pump are you running? I am starting to believe I may have had an oil delivery problem.......as well as the large clearances

your clearances are not the problem, but your machine shop should have advised you on what to run. usually run larger clearance when revving engine harder, i agree that you might have starved it. also Castrol WTF. how did you measure these bearing clearances?

What oil pump are you running? I am starting to believe I may have had an oil delivery problem.......as well as the large clearances
What oil pump are you running? I am starting to believe I may have had an oil delivery problem.......as well as the large clearances

jun high volume oil pump, gets around 27psi at idle and 80psi or so at full rpm when warm, i rev to 8500rpm usually. I also run the same oil as well (castrol edge 10w60)

Edited by unique1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Remember kids - if you can't afford to buy 2 GTRs......
    • I know people cry at the price of the Getrag 12-14k for a conversion now, but it really is a nice mid point. Not going to get change from 10k on a gearset installed.  $30k++ for sequential.   I know you run the risk of a damaged used one and parts are hard to get but as a street car gearbox its really hard to beat. If you enjoy a more traditional manual, its the choice no question.     
    • Time to decide what’s more import, your power level or your budget because you’re going to struggle to keep both 
    • Our Southern Highlands Cruise is proudly registered with “R U OK?” Day.  Sometimes the best way to check in on your mates is by getting out for a drive together. Sharing a common passion like cars creates the perfect space to chat, connect, and support each other.  A simple “R U OK?” can make all the difference. Let's enjoy the drive, the company, and look out for one another. PLEASE WEAR YELLOW FOR “R U OK?” DAY Sunday 14th September 2025 9:30AM Meeting Crossroads Homemaker Centre 10:00AM Cruise Departure Via Old Hume Hwy 11:45AM Arrival at Mittagong RSL Club Meet Location: Crossroads Homemaker Centre Final Destination: Mittagong RSL Club *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yep, its been down for a while, as I understand it it will be back soon.
×
×
  • Create New...