Jump to content
SAU Community

Stagea 350rx Four Can Be Complied ?

And

By And,
in Four Door Family & Wagoneers

 Share

Recommended Posts

loymclure Proficient

loymclure

Posted
Posted

"Emissions testing still needs to be done for the 3500cc variant

More information will be available if you are interested!"

not sure if you read the hole thing, but this is what i saw half way down. Seen a few people on here with shock horror storys of waiting for compliance due to emissions for 1 or 2 years

Guest

Guest

Posted
Posted

NO currently a 3.5 V6 can not be complied due too emissions, also no workshop will currently risk their own money and import a 350RX for emissions.

And being 2007 well that makes it even worse, if I was asked to comply one I would more then likely just laugh and walk off.

Guest

Guest

Posted
Posted
I don't understand why it won't pass emission, the 350Z, Murano and Maxima are ADM and all have the same engine, and the V35 350GT has been here for a few years.

It has not been tested which is why no one can currently comply them, they would more then likely pass but post 09/2003 testing is more expensive and will also need to be converted to RWD for the test.

And Collaborator

And

Posted
  • Author
Posted
Seen a few people on here with shock horror storys of waiting for compliance due to emissions for 1 or 2 years

It was exactly my point- i remember reading those stories too and i was wondering if things have changed since then.

Doesnt look like that, unfortunately...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • Kinkstaah
      Strange issue RB25DET wont start

      By Kinkstaah · Posted

      I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • Kinkstaah
      First time Skyline owner

      By Kinkstaah · Posted

      The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • Kinkstaah
      Chris' Toyota Mark ii JZX110

      By Kinkstaah · Posted

      I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • GTSBoy
      Chris' Toyota Mark ii JZX110

      By GTSBoy · Posted

      I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...