Jump to content
SAU Community

Recommended Posts

Hello guys, I want to change the front shocks and was wondering if it is something you can do on ur own. what are ur recommendations? easy job even for a novice? do i need a spring compressor or anything like that? can someone give me really detailed step by step guide to doing it.

cheers

Link to comment
https://www.sau.com.au/forums/topic/23232-diy-changing-front-shocks/
Share on other sites

You shouldn't need a spring compressor unless maybe you have brand new springs at the stock ride height. After a short time the springs should settle and you won't have any tension in them by the time the nut which holds everything in place is loose.

You can do it yourself if you have a spare couple of hours, even if you don't know what you're doing. Here's a brief rundown:

1. Jack front of car up and take wheels off.

2. Undo the bolts up the top.

3. Undo the bolt down the bottom.

4. Gently tap the strut sideways until it pops off its mounting. Be very careful to take the weight as it slides off so it doesn't drop onto the ground. If you're really worried, leave the top nuts on loosely so that they take the weight when it comes off.

5. Take strut and coil assembly to your workbench.

6. Use an adjustable spanner to hold the shock absorber shaft in place while you undo the nut with a normal spanner.

7. Take the spring and bump stops out, keeping note of the order in which everything comes off. Be careful of spring tension, but I've never had any by the time the nut is fairly loose.

8. Put everything you pulled off onto the new shock. If it was something like a Bilstein, you will need to assemble a couple of parts of it first. Maybe do all of this before step 1 so that you don't mix parts up.

9. when you're putting the top bit on before the nut, if necessary use your own body weight to push the spring down. It should only need to come down a couple of centimetres.

10. Push the strut assembly up through the top, and loosely do up the top nuts to hold it in place.

11. Use either a jack or your own brute strength to push the bottom part onto the bottom suspension arm.

12. Do up the bottom bolt very tightly.

13. Do up the top nuts not very tight at all. Think of how tight they would be if you could tighten them as much as possible using a screwdriver, and do them up a teeny bit tighter than that.

14. Repeat for the other side.

15. Put wheels back on, all done!

I think that's it. No responsibility taken if you screw something up or hurt yourself or the spring is so tight it shoots off across the room and takes someone's eye out :D The above has been my experience only. Your mileage may vary.

Jimx's must have been pretty tired, be prepared to have your top plate flying across your workshop when the top nut comes off.When dealing with coil springs the right tools make it a lot easier.....and safer

I think my car came with lowered springs. It's definitely got lowered springs in now (Whiteline), but yeah, I guess if it's the stock ride height be careful and use the spring compressor.

The advice given to not use the spring compressor was given to me by a Whiteline employee so maybe I could have injured myself if I had stock springs in there to start with.

Oh as an aside, the tops can be done up a bit tighter than I said. I had another look the other day and I realised it's the rears that have the really weak studs and can't be done up very tightly.

  • 8 months later...

Hey does anyone have any idea how the standard front shocks come together?

I just changed my springs on the front shocks and Im getting this strange noise from my left suspension everytime I hit a bump.

Im pretty sure I put everything back together the same way I took them out, because the right shocks seems fine, but I just want to make sure. some pictures or a description of the parts would help a lot

allready done

found out I assembled the shocks with that brass cup thing upside down

put them back on and no more clink clank

oh does anyone know where to get that extendable rubber cover? you know the one that covers the shocks so dust doesnt get in? mine is pretty much completely gone

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...