Jump to content
SAU Community

Recommended Posts

Ok so ive installed my fmic and just went for a drive and have noticed a few things.

1st question - should the pipe going into the cooler at the bottom right (looking at the front of the car) be hot and the bottom left be cold or the other way around?

2nd question - ive wound my t boost all the way down and im still hitting close to 12 pound by 3.5 k but doesnt pull as hard as when i had the stock cooler in, it just gathers boost slowly instead of bang its there, is this right?

3rd question - Is there anyway i would know if i have it done the install wrong? eg, different sounds

4th question - My car now idles around 1k where as before it would sit about 800rpm, is this cos of the cooler?

5th - Do i need to do the self learn on idle again with the pfc, it is untuned atm?

Thanks

Link to comment
https://www.sau.com.au/forums/topic/232484-intercooler-questions/
Share on other sites

If its idling high check for a loose hose clamp or vac leaks.

Might be worth grabbing a can of start ya bastard and spraying it around the fmic and all joins to see if there is a vac leak.

A fmic will soften the power delivery. I also was a tad dissapointed when I first went an fmic. BUT what it does allow you to do is run a little more boost and make more consistent power after you give it a hiding. Prior to the fmic mine felt quite crappy in third gear after I had given it a few full throttle runs.

I know itl be better in the long run with a tune and when i get my new turbo (gota still save a bit more) but i just didnt think it would be so different, it feels like ive lost power and not gained any. Soapy water around the clamps would do a similar thing wouldnt it, if checking for leaks? The blow off sounds sooo much better, bugger putting as aftermarket one on now!

Edited by Damo_c

1. Yes

2. Your running a larger cooler, more boost and no tune. Of course its not gonig to be great

3. Not really

4. Vac leak maybe, as stated.

5. No, but that comes as no surprise with point #2. - YOU SHOULD NOT BE TRYING TO HIT 12PSI UNTUNED.

YOU SHOULD NOT BE TRYING TO HIT 12PSI UNTUNED.

So what are you trying to say, that i should not be running a hi flow (to4 front vg30 rear) at .9bar with standard injectors, fuel pump, afm and ecu?

I think im at the limit though, breaks down when it hits 1bar so when it spiked to 1.2 it was not happy at all.

it may be wrong but from what i have read an untuned pfc is at about the same level as a standard ecu, is this wrong?

I don't know about that but... standard ECU is not much good once you start modifying the engine. The point of a PFC is that you can change timing, Air/fuel ratios etc - untuned its just a waste of $$$ ( and if you've bought it second hand it could have a tune suited to a set-up which is quite different from what you have and could in fact be worse than your fact ecu).

The maps are basically a direct copy HOWEVER the load points used for a given airflow value is slightly off as the PFC runs a 20x20 vs the std ecu's 16x16 load map.

As a result the pfc usually ends up running a tad more ignition at wot which usually causes the car to det. In my experience anyway. Depends on the level of tune/mods/boost. Would likely be fine for a car running std boost.

Yes it is untuned, i was guna save some money for a turbo then a tune. I drive the car very easy at the moment. I dont wanna waste getting a tune then in 2 months having to get another tune after getting the turbo. I hit 12 psi maybe 5 times since ive had the pfc put in, yeah i am risking a bit of engine damage but when the car is my daily driver and i need to floor it a bit to let a cop go thru or something like that, which happened only a week or so ago, so be it, but ive been very careful as to change at about 2800-3000 light accelaration so bugger all boost. The tune will be happening very soon cos now youve gotten me all worried. Gota use the left over moeny from my wedding to do so. Ive got the t boost wound all the way down but its still boosting up. The pfc is brand new so there is not another cars tune on it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...