Jump to content
SAU Community

Recommended Posts

to day i ran my 33 gtst down the 1/4 after a couple of passes at 12.2@123mph with a crap 60 foot of 2.2, i ran my best 60 foot at a 1.8 but right after i hit second gear a all mighty bang went off (back fire) and the car lost power for a split second so i came off the gas until 3/4 track and jump on it again and it felt fine ,i got back to the pit area and i noticed on when you lightly press the gas it runs like its missing ,i also noticed this in the last three runs leading up to my last run ,now i think its ???????? but what i would like is some input from some sau members on what they think it could be......thanks.

Link to comment
https://www.sau.com.au/forums/topic/232530-what-do-you-think-it-could-be/
Share on other sites

could be anything

sounds like plugs need changing most likely.

yes ill give that a go today!!

pm-r33 im making 304kw atw but i think there is a little more to come as im running 17.5 psi

Edited by WARLORD

i had this problem with my car, it turned out to be the intercooler pipe

one of the vacuum lines came off the fuel pressure reg and for some reason (im not gonna pretend i know what im talking about here) it backfired and pretty much just died in the arse, it would idle but wouldnt accelerate, check your cooler piping, find the loose hose and reconnect it

ps. this was a right pain in the arse to diagnose and fix at 2am on scarb beach rd in the rain :P *shakes fist in a menacing fashion*

intercooler all good .

what i have noticed is that when the car is cold its fine andwhen its hot it plays up.

could be coil packs.i dont think its normal to happen so low in the rev range but i guess anything can happen ,there only 3 years old ,ill have to check them

has anyone got any more ideas

intercooler all good .

what i have noticed is that when the car is cold its fine andwhen its hot it plays up.

could be coil packs.i dont think its normal to happen so low in the rev range but i guess anything can happen ,there only 3 years old ,ill have to check them

has anyone got any more ideas

did you check the inside of the 90 deg bends the run through in in left inner gaurd

,

earth wire .....i noticed the earth wire on the turbo side is not there. does anyone have pics to what it is connected to cos ive got the earth wire i know one side is on the exhaust manifold but have no idea what it plugs into.

o and could this be part of my problem. :D

hey warlord

try pumping compressed air into your intake system with a compressor.

i do this about every 6 months as it shows up any leaks in the system.

the easiest way i have found is undoing the clamp where your afm is, getting a plastic freezer

bag putting over the afm and then reinstalling the afm and doing the clamp up.

you can then use a trigger nozzle from your air comp stick into the fuel reg hose and pump 2 bar

into your intake system.

a lot of leeks wont show up unless there under pressure so this is the quickest and easiest way that i have found

and works every time.

and also a poor earth wont do the engine any good put it that way.

hey warlord

try pumping compressed air into your intake system with a compressor.

i do this about every 6 months as it shows up any leaks in the system.

the easiest way i have found is undoing the clamp where your afm is, getting a plastic freezer

bag putting over the afm and then reinstalling the afm and doing the clamp up.

you can then use a trigger nozzle from your air comp stick into the fuel reg hose and pump 2 bar

into your intake system.

a lot of leeks wont show up unless there under pressure so this is the quickest and easiest way that i have found

and works every time.

and also a poor earth wont do the engine any good put it that way.

thanks !!!!!

what do you recommend i use for a earth cable, and the best place to put it.

Yeah i do. Hope i can explain this well.

Behind the power steering resevoir, on the strut tower down near the turbo intake, there should be a little gold piece of metal, the black connector just slides over that.

Yeah i do. Hope i can explain this well.

Behind the power steering resevoir, on the strut tower down near the turbo intake, there should be a little gold piece of metal, the black connector just slides over that.

that has got to be one of the best descriptions i have ever read,,,i new where to go and found it it 2 sec thanks.....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...