Jump to content
SAU Community

Recommended Posts

Nissan do this, it means you have the special million dollar winning car,

Nah, but unscrew the 4 screws in the speedo, pull it out, check the speedo cable is plugged in properly, if it is, then check the sensor at the other end(gearbox end is still working, follow the cable up, sometimes they snap, if it's buggered just get a new speedo cable, if it's not, then you might need to take it to a mechanic, something must be stopping it from spinning)

If the speedo and P/S are still working, then it shouldn't be a problem with the cable.

The Japanese seem less opposed to fiddling odometers (winding them back). It's possible some sort of damage was done that prevents the odometer going past 100k.

I have the same problem as mine started to play up at 75000kms and fixed itself.

It has now hit 80000kms and wont budge, even the trip meter has stopped.

So I pulled it apart today and had a look seemed easy enough but I couldn't find anything wrong so I just pushed the odometer numbers gently past 80000 with a small screwdriver.

Dunno if this has worked yet as my radiator is out and I cant drive it.

Will let you know as soon as I do tho.

On a side note my boost guage seems to be playing up.

When Im idling the guage reads 0 pressure not vacuum, but when I start to boost it it climbs up.

Also noticed that when the car is off it falls down to 7 deg vacuum.

Any ideas????

I have exactly the same problem.......

the ODO meter stop when reaching 89999kms

yes, four 9 and doesn't go past the 90000kms!

and the trip meter also stopped........

I opened it up and can see nothing wrong

went to wrecker to buy a used one.

realise that the one I had......doesn't have the P, R, N, D, 1, 2......at the centre......

so I am guessing it is for a manual car

and now maybe I could understand why the O/D light doesn't turn on

so what's the reason behind the not running odometer?

i heard that when your car is moving, you shouldn't reset the trip meter..........but I need confirmation about that lol

and also I think it stopped before I reset -_-"

This is what we were concerned about at 5 mins to midnight on 31/12/99 eh?

Had an N13 that did the same thing, and after about 2 months, the odo moved on. Might have been after speed hump rather than a chicane.... Silly isn't it!

Rubber Mallet? I'll LOL if that works!

the car's odometer just stopped in shock when it realised it was the second time it had clicked over 100,000klm :( I guess they wound it back a fair way.

no idea how to fix it but it is pretty common with these cars

pull it apart and look for the cogs from memory there is one white one and severl black ones, check to see if they are all lined up and "meshing" nicely in there, also make sure no damage to the shaft and that everything is plugged in! Gl hame.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
×
×
  • Create New...