Jump to content
SAU Community

Odometer Stopped!

chrissyo

By chrissyo,
in General Maintenance

 Share

Recommended Posts

skybarge Community Regular

skybarge

Posted
Posted

Nissan do this, it means you have the special million dollar winning car,

Nah, but unscrew the 4 screws in the speedo, pull it out, check the speedo cable is plugged in properly, if it is, then check the sensor at the other end(gearbox end is still working, follow the cable up, sometimes they snap, if it's buggered just get a new speedo cable, if it's not, then you might need to take it to a mechanic, something must be stopping it from spinning)

blind_elk Grand Master

blind_elk

Posted
Posted

If the speedo and P/S are still working, then it shouldn't be a problem with the cable.

The Japanese seem less opposed to fiddling odometers (winding them back). It's possible some sort of damage was done that prevents the odometer going past 100k.

Stormchaser Enthusiast

Stormchaser

Posted
Posted

I have the same problem as mine started to play up at 75000kms and fixed itself.

It has now hit 80000kms and wont budge, even the trip meter has stopped.

So I pulled it apart today and had a look seemed easy enough but I couldn't find anything wrong so I just pushed the odometer numbers gently past 80000 with a small screwdriver.

Dunno if this has worked yet as my radiator is out and I cant drive it.

Will let you know as soon as I do tho.

On a side note my boost guage seems to be playing up.

When Im idling the guage reads 0 pressure not vacuum, but when I start to boost it it climbs up.

Also noticed that when the car is off it falls down to 7 deg vacuum.

Any ideas????

KJS Enthusiast

KJS

Posted
Posted

I have exactly the same problem.......

the ODO meter stop when reaching 89999kms

yes, four 9 and doesn't go past the 90000kms!

and the trip meter also stopped........

I opened it up and can see nothing wrong

went to wrecker to buy a used one.

realise that the one I had......doesn't have the P, R, N, D, 1, 2......at the centre......

so I am guessing it is for a manual car

and now maybe I could understand why the O/D light doesn't turn on

so what's the reason behind the not running odometer?

i heard that when your car is moving, you shouldn't reset the trip meter..........but I need confirmation about that lol

and also I think it stopped before I reset -_-"

GTR-N1 Grand Master

GTR-N1

Posted
Posted

This is what we were concerned about at 5 mins to midnight on 31/12/99 eh?

Had an N13 that did the same thing, and after about 2 months, the odo moved on. Might have been after speed hump rather than a chicane.... Silly isn't it!

Rubber Mallet? I'll LOL if that works!

Duncan Grand Master

Duncan

Posted
Posted

the car's odometer just stopped in shock when it realised it was the second time it had clicked over 100,000klm :( I guess they wound it back a fair way.

no idea how to fix it but it is pretty common with these cars

H@ME Mentor

H@ME

Posted
Posted

pull it apart and look for the cogs from memory there is one white one and severl black ones, check to see if they are all lined up and "meshing" nicely in there, also make sure no damage to the shaft and that everything is plugged in! Gl hame.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • pacman_1219
      Blue/grey smoke after idle

      By pacman_1219 · Posted

      Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • MBS206
      R33 Fuel Pump & Brakes after alarm swap

      By MBS206 · Posted

      Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
×
×
  • Create New...