Jump to content
SAU Community

Recommended Posts

^^ i totally agree with u dude. i really need to piss off this emanage, i watched him tune it, theres f**k all room for fine adjustments with the emanage... could also be the fact that i have a central 20 ecu as well, might be conflicting somewhere??? ahhh if only pfc were cheaper...

Your call but I reckon a little more turbo and a little less boost , jeez those 2535's aren't real big on the hot side and the restriction generally leads to a thermal thrashing .

Pro S and IW GT3071R's cost a bit but you get much less restriction from them on the hot side and a more modern compressor wheel as well .

Again IMO the whole dump flange system from the std Hitachi footprint is not the best one to go beat the world with .

I understand that bolt on turbo solutions have to keep it but it has its limitations .

A .

Easy answer is throw on a Nissan RB25 wastegate actuator and get the boost down under control. Boost alone wont kill the engine, temperature alone wont. Revs alone wont and coolant and oil temps wont kill an engine alone.

As others have pointed out, you are borderline on boost, and its the worse sort of boost in that the engine isnt working effeicently with effecient exhaust of combusted gases. Its choking on the gases. So combined with the bog revs and high coolant / oil temps you see drifting....like i said i would be getting the boost back down to 13psi. Then get the breathing on the engine sorted.

hey seriously i would just dump some extra fuel up top to be safe, the tune is good but if you cracked 6th it was detonating and i would reckon that the tune was the cause.

Knock 3 degrees off the map and add some fuel up near the limiter (depending on how you drive)

im happy to have a look at it one night if you want.

^^ i totally agree with u dude. i really need to piss off this emanage, i watched him tune it, theres f**k all room for fine adjustments with the emanage... could also be the fact that i have a central 20 ecu as well, might be conflicting somewhere??? ahhh if only pfc were cheaper...

I have NA sr20's with td06's runing 19psi with emanage no problems. The emanage is a great unit if the user knows what they are doing.

That boost and those a/f ratios at the top end; you're asking for trouble.

RB25's are known to have weak ring-lands and the boost and leanness of the tune will generate more heat which can cause issues. I personally wouldn't risk it.

I consider anything over 12:1 a/f ratios, on a std RB25 and doing track days a BIG risk.

I ran 18psi, with 11.5:1 a/f ratios and still managed to crack a ring-land, pics below. All other components were in top nick, even the piston top, bore, etc of the cracked piston where completely undamaged.

Don't worry about split pipes or stainless; just get a custom made bell-mouth mild steel dump from a good exhaust shop. Should not cast you too much.

that is the result of det most likely nothing to do with the a/f. I have a few tough mid 300rwkw rb's running leaner than 12.2:1

that said in DJEMS position i would fatten it up as i know nothing of the timing map.

that is the result of det most likely nothing to do with the a/f. I have a few tough mid 300rwkw rb's running leaner than 12.2:1

that said in DJEMS position i would fatten it up as i know nothing of the timing map.

Wouldn't det have shown on top of the pistons?

ie: pitting or rough'ish surface.

Apart from the cracks between the ring-lands, everything else was in pristine condition.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...