Jump to content
SAU Community

Serious Problem With R33 Gtst

l0WRB

By l0WRB,
in Engines & Forced Induction

 Share

Recommended Posts

l0WRB Mentor

l0WRB

Posted
Posted (edited)

posting on behalf of a friends r33 which has serious problem

mods

rb25det series 1

splitfire coilpacks

cooler

exhaust

10psi

stock ecu

items we have tried and replaced with items off my car.

afm

3 different fuel pumps, now running stock rb25 fuel pump

coil pack igniter

cas

fuel regulator

basically im gonna try best describe what the car does.

sometimes the car will drive fine for half a day or all day then all of a sudden the car will start surging just while driving along at 60kmph or 100kmph

this is when the fun begins, once the car starts surging it will basically just cut the ignition and u have to put ur foot flat to the floor to keep the engine going, thing is the car doesnt rev or go anywhere with it flat

to the floor, u can hear the turbo spooling and the bov goes off a bit but the motor isnt reving or accelerating and thats flat to the floor for about 20-30secs, and if u take ur foot off the accelerator the car will die

and u have to roll over side of the road and kick it over 3-4 times before it will go again.

the fella has a powerfc there aswell that he has tried plugging in and using on base map but it does the exact same thing.

does anyone have any ideas? we r out of ideas.

have tried replacing the above items but nothing has fixed it.

Edited by l0WRB
Link to comment
https://www.sau.com.au/forums/topic/233713-serious-problem-with-r33-gtst/
Share on other sites
l0WRB Mentor

l0WRB

Posted
  • Author
Posted

well the car u have to hold the accelerator flat to the floor to keep the motor from stalling and u can hear the turbo spooling still but the car doesnt accelerate or go anywhere like uve got it in neutral, and if you just let your foot of the accelrator the car will die and wont start again until u pull over and kick it over 3-4 times.

l0WRB Mentor

l0WRB

Posted
  • Author
Posted (edited)

fuel filter has been replaced, plugs has been replaced, vacum leaks have been checked all clamps.

havnt checked for bad earth or anything? only thing i cant think of that is earthed is ya igniter pack?

hmmm pretty sure its all bolted on near towards coilpack no6

its really fkn hard 2 guess wot it is though

the car starts and runs perfect and then all of a sudden it will just do this out of the blue

wether u flog or baby the car.

Edited by l0WRB
RBwhatever Veteran

RBwhatever

Posted
Posted

So you've checked all the cooler piping and joins?

When my pipes partially blew off it wouldn't rev past 4grand, wouldn't make full boost obviously but was still spooling, it was just a massive air leak that would only open up under pressure. Off boost it drove fine. Made the car run pretty crap though under boost.

....ummmm blocked cat maybe?

l0WRB Mentor

l0WRB

Posted
  • Author
Posted (edited)

yeah its not a vacum leak or join

the car WONT accelerate or make any boost, but u can hear the turbo spooling as u hold ur foot flat to the floor for 20-30 secs.

car doesnt DO ANYTHING at all cept roll along, its messed up.

car is running gutted cat. hmmm

Edited by l0WRB
Al Grand Master

Al

Posted
Posted

If the car is lowered remove the front right wheel, then the guard cover, and check to see if the loom as been damaged by the wheel itself. I have seen lowered cars rub through the looms and create massive shorts and problems. One even caught fire and the loom had to be replaced.

Is it more likely to happen in the wet, hot days, after X amount of driving, on rough roads, etc.

Also make sure you carefully check all the wiring, especially in the engine bay.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...