Jump to content
SAU Community

Recommended Posts

Item: Garret 2860-7

Age: puppies

Condition: Very good

Price: 2k Delivered

To Fit: Direct RB26 bolt-on

Location: Townsville QLD

Contact: PM me or call 0431520274

Comments:

I bought these turbos some 3 months ago. I havn't fitted these to my car yet, they have travelled less then 500km's by the old owner who purchased them brand new.

Reason for selling is simple, My motor is coming out and getting a freshen up and rebuild so I want something bigger..

Will post pics tomorrow.

Couple of member's pm'd me asking if id sell, so here is your chance, direct bolt-ons for your RB26dett in fault-less condition.

Edited by Tomek
Link to comment
https://www.sau.com.au/forums/topic/234002-garrett-2860-7-turbos/
Share on other sites

what psi can you run on stock internals and then what power would it make?

How long is a piece of string? ;)

All pending how much you want to push through them... I was going to go for 19-20psi through my virgin motor in chase of 330kw..

  • 3 weeks later...

Horsepowerinabox sells those tubbies at like 2200AUD a pair - brand new.

So what´s the best price you could do inclusing shipping to 70378 Stuttgart, Germany?

A friend of mine is after those...

  • 3 months later...
whats mods done to the engine buddy?

Everything is internally stock, runs a bosch 044, 600x300x76mm fmic, custom piping, hks dumps, straight through 3" Trust PE2 exhaust, and a linkplus g3 computer, splitfire coils.

And it's just a 25box sitting behind the 26 in the 180.

  • 3 weeks later...
  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...