Jump to content
SAU Community

Recommended Posts

  • Replies 60
  • Created
  • Last Reply

Top Posters In This Topic

Err not that it's really going to help much.... but anything stand out obvious wrong from these couple of photos lol. The oil feed banjo isn't sealing 100%.. i need to fix that but I don't think that would be doing it..

IMG_0715.jpg

IMG_0716.jpg

IMG_0718.jpg

Hey yeah there is a gasket... It doesn't go to 0 straight away.. if i drive it it slowly climbs to a tiny bit below 0 and then doesn't go up any higher even if foot is flat.. grrrrr

that sounds like a problem, as putting ure foot down to the floor regardless where in a non turbo motor should give 0 vaccume, and on a turbo motor should give 0 vaccume then boost, i just added you on msn so i can ask you about it there instead of in a million posts

Hey yeah i can the wastegate flips open and closed without the arm attached to it just as easily as the old one.

I just went for another drive.... a big one this time... at 47% throttle (i went more than this) it's 58% airflow @ 4600rpm. It's like nothing nothing nothing then if i give it more the boost goes up to like 5psi and then when i back off the bov goes off like normal but the turbo makes a really faint spool like it does when you blow a cooler pipe so perhaps it is just leaking somewhere afterall.. Is a highflow going to make it THAT much laggier?:s Perhaps it's been bored out too much?? Doubtful as it still utilizes the same front and rear housings. I'm just waiting for someone to say that it will be different to drive with a highflow than standard but it's not that..

Which leads me to my next question... if the turbo is capable of producing even small amount of boost does that rule out that the turbo is the problem?? Or not necessarily...

*checks all hoses and piping again..*

Thanks for everyones help...

if the gate was stuck open it would go into vacuum instantly no problems and build some boost

it would just be mega laggy to build a useful amount of boost

but getting to 0 should be almost instant with gate leaking or not

it sounds like your manifold isnt pressurize, ie; your engine is atmo

this explains why you cant reach 0 vacuum

Yeah maybe you just forgot to tighten a hose clamp and its half blown off.

If its a bush bearing highflow it will be laggier again over a turbo thats BB of the same specs or a standard turbo. It won't deliver the boost as nice as a BB.

Yeah i'm gonna pull the dump pipe back off... make sure the wastegate flap is 110% closing correctly and make sure the arm is pulling it shut... when that's off also make sure the wheels are still spinning together and are tight... after that I think there's nothing more i can really do and will gladly pay a shop to fix whatever it is.

im having a brain fart but it seems like I have had this problem before. Maybe some how that turbo is out of spec?? The boost is suppose to be built up in the compressor housing and then distributed throught out the intercooler piping. Almost sounds like it may be sucking but not pushing if ya know what I mean. check the gasket on the comp housing. I think that fixed my problem before. It suxed trying to find one. or take the turbo off and get it checked by a pro. Or if ya have a freind with anouther turbo borrow it.

Good luck

Just had another look at pics.

1) Move your pressure source AWAY from your FPR.

You should NEVER tee things off the FPR signal line. You can cause pressure drops when putting things on that flow air etc.

2) Your hose clamps on the hot side of the intercooler to turbo seem to not be sitting right. Undo them, line them back up, redo them.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
    • Oh, and as for everyone with their fuel economy changes, I switch between E10 and 98 in the company car. Even do when I had personal cars that could run on E10. You know what changed my fuel economy in any noticeable way? How I drove, and where I drove. Otherwise, say on full tanks of just back and forth from work only (So same trips, same sort of traffic), couldn't notice a difference that I can correlate to the type of fuel in use. In the current vehicle, that's over 42L of USABLE fuel. While 98 is all "more energy dense", it also has higher knock resistance as it takes more energy to get it to ignite too. The longer hydrocarbons, typically more tightly bound. So running the same ignition map, can also produce less power, if there isn't enough time to get it all burnt through properly, as yep, the flame propagation speed is different from lower octane fuel to higher (Higher has a lower flame propagation, due to the more tightly bound and harder to self ignite funs. This is also typically where, a vehicle that is designed purely to run on 91 (Whether it be E10 or normal 91) usually sees absolutely no real world difference in fuel economy for the normal man, woman, or dog.
    • We've got some servos around me that have 91 with E10, 91 (no E10), 95, and 98. At those stations the change from 91 E10 to 91, is typically around 8c/L.   But lets not get started on the price of fuel in Oz. It's ridiculous. All the service stations around me, bar one, the price of fuel has been over the $2 mark per litre for the cheapest, 98 being around $2.45. That one service station is a CostCo, fuel from it comes from the same refineries, and makes no pitstops, it runs great, including the 98. In fact, I've had no issues on CostCo fuel, but plenty of issues at other stations!. The CostCo fuel, was $1.65 roughly this week for 94 with E10. $1.88 for 98. Servos directly across from it, $2.10 for 91 E10, and $2.48 for 98. The part I had to laugh at? If I drive multiple HOURS away from Brisbane, say out near Nanango, or Kingaroy, or even out to Goondiwindi, the price of their fuel, is the same as what it is at the CostCo... Oh, and that BP servo at Goondiwindi is HUGE and goes through epic turnover of fuel, so it's not sitting there for weeks going to shit. And what blows me away, my mate is one of the people who drives the Fuel Tanker all around QLD, delivering to all those places. At the same company his previous role was doing the "local haul" deliveries... Same truck, same driver, same pickup point it all comes from. So you tell me, how the hell it is 60c/L CHEAPER for fuel, when nearly all else is equal, except they require a B-Double to drive half a day out of Brisbane, and half a day back, every second day, compared to the delivery that can be under 30 minutes drive from the fuel pickup point... Not to mention, go five blocks down the road, and Ampol to Ampol will vary 30c/L... And I've had this conversation with my mate... The way it's priced, is just typical, pure and utter rubbish... He also does runs from Brisbane, to all over QLD, down to Newcastle, Sydney, Nowra, Melbourne, Geelong, and even out to parts of the NT depending on the companies needs. His main stuff is all the longer distance away from home for a few days at a time, then when he's back, he loves to just pickup extra shifts wherever he can in whichever truck, hence all the weird different places.   Oh, as for getting E10 into all the fuels in Australia... It was very quickly highlighted, that we don't have enough biomass available to use to make E10 sustainably like they require, and it would dramatically cut into our, and the worlds food chain supply...   I vote we all just start running on liquid methane gas... Plenty of that just getting tapped off at tips from underground decay... (Note, this is pure just stupid commenting. I could very easily highlight the reasons its not a good idea especially on scale...)
    • Am I correct in assuming that the R35's are getting the classic skyline haircut off the odometer?  Quick search on carsales, there are 33 08 and 09 GTR's for sale, only 2 of them have more then 100,000km's on them (116,075 and 110,000 respectively).  And somehow there are about 25 for sale with around 60,000kms? Looks like the classic skyline haircut to me =/
×
×
  • Create New...