Jump to content
SAU Community

Recommended Posts

This isn't in anticipation of the dyno day is it???

:bahaha:

Boosters are shit, they only raise 0.1 of a octane point.

There's really one foolproof way and that's 10% or more toluene.

That gives real full points octane boostage. But I wonder if it's worth it. It certain is in track situations.

T.

Link to comment
https://www.sau.com.au/forums/topic/23444-octane-booster/#findComment-501526
Share on other sites

my experience was quite crap dude....

filled up with mobil synergy 8000 and a bottle of octane booster a couple of nights before my maiden EC off street drags with the wrx.

car started misfiring and it couldnt shake it till after EC...misfired all the way down the quarter but still ran a 13.5s...

Link to comment
https://www.sau.com.au/forums/topic/23444-octane-booster/#findComment-501808
Share on other sites

I used octane booster for racing type affairs when my tune wasn't the best. Obviously only an advantage when using the best fuel available to you. On another note, also very handy for country trips where there is only shitty regular fuel available.

I have used the Nulon Pro-Strength as I was stuck with regular in country NSW and it worked a treat.

Adrian

Link to comment
https://www.sau.com.au/forums/topic/23444-octane-booster/#findComment-502148
Share on other sites

I use the Nulon stuff as well. Your car has to be tuned for it to be effective so you can't just chuck it in and expect it to work. Everyone that tells you their car ran rough when they tried it is finding this out.

More people say it doesn't work and some say it slowly wrecks your internals but no one has so far backed it up with evidence as far as I've seen.

Link to comment
https://www.sau.com.au/forums/topic/23444-octane-booster/#findComment-502731
Share on other sites

Originally posted by Blitz

Does some interesting things to spark plugs - as far as I know you can use you as long as your engine is running hot enough to burn it up. Anyone care to clarify?

This may seem like a controversial statement:

"You should run your car on the lowest octane fuel it is designed for."

But if you look into what happens during combustion it becomes a bit clearer. For the best performance (be it economy or power) there needs to be a controlled burning of the fuel air mixture. This is dependant on pressure, mixture, fuel, temp., ignition and whatever else.

By raising the octane rating of the fuel it will resist detonation (where the fuel/air mix explodes rather than burns), i.e. the infamous "detonation" or "pinging". Put simply, the higher the compression ratio (or boost) then the higher the octane rating required for the fuel.

Now, if you are running 98 octane in your engine that is designed to run on 91 then all the fuel is not being burnt during combustion as the temperatures and pressures are not high enough. Therefore a reduction in performance will be the result.

If your engine has a knock sensor fitted then it will automatically adjust the timing to suit whatever fuel is going through the pipes for the required performance. That's about it as far as my technical knowledge goes.

Now someone please correct me if I'm wrong:

The knock sensor is also called a lambda sensor and measures the unburnt oxygen via the oxygen sensor, right? If the system is a closed loop system then it can adjust the timing to suit the fuel used.

The RB25DET (stock ECU) does not have this as you have to tune it for the fuel being used , right?

Any corrections appreciated. :)

Link to comment
https://www.sau.com.au/forums/topic/23444-octane-booster/#findComment-504126
Share on other sites

Avgas will coat your O2 sensors as well as block up your cat convertor! I Always run Optimax or Ultimate with Wynns race formula or Nulon prostrength when iwind the boost up on the Sx as insurance against pinging. I would have thought that ALL Jap imports would benefit greatly from 98 fuel & a good octane booster as there tuning is designed for 100. My Mates 300zx improved considerably from 98 & NF blackoctane booster as he could put another couple of degrees timing into it. He Run 13.2 then with timing dropped to 12.8.

Link to comment
https://www.sau.com.au/forums/topic/23444-octane-booster/#findComment-504292
Share on other sites

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah in that case, pulling the dent out. Event a very slight dent can create a lot of work filler-wise and there is a strong chance the panel won't be the factory shape when you are done (as the dent will result in a new high point created somewhere, then everything is brought up to that new high point... but the panel shouldn't be that high if that makes sense).  So you've filled and primed the panel and it is flat, why would you go back and remove the primer and add more filler? 
    • Something else I have been faffing with while the car was off the road is making the AC work. Assuming the car isn't at a thermal limit the idea of having AC while waiting in line to go on track sounds delightful. I have actually been lugging around the weight of the entire system since 2018 when the RB25NEO went in without it working at all.  The main reason was in the first few events before I got around to re-gassing it the rubber hose that runs under the manifold had the factory heat wrap/sleeve fail resulting in this: ~2 years ago I purchased a complete used R32 AC line set but when I finally went to install it the line i needed was different where the expansion section is I found a local place that was able to replace the rubber section and re-crimp. They also added some modern heat sleeve to the hose Tight fit but fingers crossed this is the last physical piece of the puzzle needed
    • the top black section is bonded to the silver section with some form of rubber. I assume to isolated NVH from the box
    • Plan B? Get someone to machine up a metal bush/collar/whatever it needs to be to replace the rubber? I haven't had a close look at that part recently to have a proper feel for whether that's possible. But it might be easy.
    • I do not want to install a short shifter and the only other stock throw shifter I have seen is the Nismo "Rigid shifter" for $290 So plan A is to fill it with sikaflex to stiffen it up and hope for the best
×
×
  • Create New...