Jump to content
SAU Community

Recommended Posts

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

hey just wondering if i can have your sun visors? what color are they need both and the brackets that clip into the roof

hopefully they are grey and what condition

how much pm me?

still got the rear bumper? if its in good nick i'll take it, i never get on here though, give me a call or txt on 0415626733 and we'll sort something out

I do, bar has no major damages, just a few scratches.

Do you have a standard leather gear knob in good condition?

Only have aftermarket gear knob (in red leather).

got pics of the sunroof?

I have a pic, here it is:

post-49183-1224028936_thumb.jpg

Sunroof is a genuine nissan one. Opens both ways.

hey just wondering if i can have your sun visors? what color are they need both and the brackets that clip into the roof

hopefully they are grey and what condition

how much pm me?

I do have them. They are grey, but they would need a clean. (probably previous owner(s) were smokers)

You can have the pair with the brackets for $40.

Complete sunroof with all its attachments for $250.

highly intersted would you post to melbounre 3150?

wouldnt happen to have

gtr injectors

gtr fuel pump

r33 stock turbo

by any chance?

highly intersted would you post to melbounre 3150?

I can post, but i will need to pull the sunroof out measure and weigh it to get it priced up for freight. To do that i will need

assurance that you were certain of buying, like a deposit.

I do have gtr injectors and fuel pump, but they wont be for sale until for another month or so as i will be using them to run

the GTR (standard fuel setup till i change it when i go for a tune). Sorry dont have 33 turbo.

Items sold:

  • R/H A-pillar trim
  • Rear bar
  • Front bar & bar indicators
  • Gear stick boot and surround.

Plenty more parts i still have, so if your in need of something let me know and i may have it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...