Jump to content
SAU Community

*** Hd Clutch Group Buy #2 ***


Recommended Posts

Hi guys

I'm running a group buy for NPC Products

SPECIFICATION:

5puk Ceramic

1200+ pressure plate

Rated to 350rwkw or about 300awkw

NPC724B5.jpg<<Click

The pressure plate I use is a standard Exedy cover that is pulled down and fitted with the same diapghragm spring nismo uses in some of their pressure plates. I then modify the Exedy pressure

plate to suit a 5 puk sprung center disc that I make using a 4.2 ltr patrol clutch plate.

SUITS:

FJ20, RB20, RB25, mild RB26 Push type Clutch

for a pull type clutch he can do that for $650

NORMAL Price $643.50

GROUP BUY PRICE $550

Shipping Via Australia Post to ANY location is $30

we need a minimum of 4 clutches but i would like to try for 5 orders

SPECIFICATION:

Lightened Billet flywheel 1 piece - Nissan Skyline Revsolution Flywheel- R32, R33, R34, RB20DET, RB25DET, RB26DETT, 6.5kg

RNF03.JPG<<Click

SUITS:

FJ20, RB20, RB25, RB26DETT with the 5 puk clutch

we need a minimum of 5 Flywheels for the group buy price

NORMAL Price $425

GROUP BUY PRICE $350 if we only get a couple of orders for flywheels I've negotiated a price of $400 so still a small saving

Shipping Via Australia Post to ANY location is $30 NOTE: if ordering a clutch also shipping will be combined for $30

SPECIFICATION:

Twin Plate Clutch - Note: Push type only

COMPOSIT.jpg<<Click

NORMAL Price $2200

GROUP BUY PRICE $2050 - NOTE to fully rebuild this twin plate Doug tells me your looking @ $350-$400 A LOT cheaper that Japanese clutches

Shipping Via Australia Post to ANY location is $30

THIS GROUP BUY WILL RUN FOR 4 WEEKS FROM THIS DATE Monday 8th September LAST PAYMENT BY DIRECT DEPOSIT FRIDAY 3RD OCTOBER Order will be placed WEDNESDAY 8th OCTOBER

***GROUP BUY Rules DON'T be ringing Doug to ask him questions all questions to be directed through me if the information isnt already supplied***

If you think you would like to join in on the Group buy Find my Bank Details Below and you can deposit money at you leisure i will PM you with confirmation you payment has cleared and asking for shipping details

Thank you

Steve

Commonwealth Bank

Stevan Rosskogler

BSB: 065000

Acc. 10335841

NOTE: there is alot of Q&A in the previous GB thread >>Here<<

Clutches

1. /2on - 5puk Clutch

2. CraigR33

3. Fabs_32

FlyWheels

1. /2on

2. Fabs_32

3. Andrew M.

Link to comment
https://www.sau.com.au/forums/topic/235235-hd-clutch-group-buy-2/
Share on other sites

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

lol yeah sorry guy i check and check my first post and missed it TYPO fixed

sorry Joel no twin for you unless you have a spare 2k, but you quiet happy with yours atm :D

i have R34 GT-T and on the npc site, the 5puk clutch seems to be $1023 (it says R34 GTR, but it has RB25DET in the line, so im assuming its the GTT clutch) just want to double check the price, that its only $100 more over the push type r33 clutch ($650)? decent saving considering i was looking at buying the exedy 5 puck hd clutch from sliding performance at $739 dollars..

so to clarify cos Madaz's answer was not really clear, I will need the $650 single pull tupe for the 97 gtr?

Does the twin plate include the lightened flywheel for the $2050?

All twin plate clutches include flywheel

Hi Michael yeah from what i gather the 5 puk can be made as a pull type clutch and that indeed will suit all RB engines what Doug tells me is the pull type clutch will handle a little more power as there a 10" clutch where as the push is a 9" and yes add $100 on top of $550 for a pull type, i hope this is clear

EDIT: the $1023 GTR clutch has a pressure rating of about 3600lbs dont be mislead you wouldn't get that clutch for $650

sorry Simon i thought my response was very clear i will say it another way all GTR from R32 v-specII (NOT SURE about normal v-spec) and newer all take the pull type clutch

NOTE: the NPC twin plate clutch only comes as a push type clutch you can however convert a pull type clutch system too push

Hi Michael yeah from what i gather the 5 puk can be made as a pull type clutch and that indeed will suit all RB engines what Doug tells me is the pull type clutch will handle a little more power as there a 10" clutch where as the push is a 9" and yes add $100 on top of $550 for a pull type, i hope this is clear

sorry Simon i thought my response was very clear i will say it another way all GTR from R32 v-specII (NOT SURE about normal v-spec) and newer all take the pull type clutch

NOTE: the NPC twin plate clutch only comes as a push type clutch you can however convert a pull type clutch system too push

Not 100% sure but you might want to check with Doug on the price for that pull type. That's a fair chunk cheaper than the last few I remember from him.

See the $1023 clutch >>here<<

Not sure mate.

The R34 GTT uses a pull type clutch just like R33/34 GTR but that is a push type clutch in the picture. That $1023 clutch pictured on his website is to suit RB20/25DET pre Neo and R32 GTR pre series 2.

The pull type clutches should be up around the $850 mark, that is why I was questioning the price of $650.

yeah don't go by pictures between all the different prices they all look like the same 5puk

i can only go by what Doug tells me his standard price for the 5puk is $643 $100 on top of that for being Pull would be $743 correct so with the group buy your now looking @ $650 the same saving the push type gets from the original price

yeah don't go by pictures between all the different prices they all look like the same 5puk

i can only go by what Doug tells me his standard price for the 5puk is $643 $100 on top of that for being Pull would be $743 correct so with the group buy your now looking @ $650 the same saving the push type gets from the original price

Yeah I know about the pictures.

That's a good price for a pull type clutch, I understand you just go off what Doug tells you...I just wanted to make sure you weren't underselling yourself as the pull type clutches (last time I spoke to him) retailed for over $1000.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...