Jump to content
SAU Community

Willall Racing Buys Australia's First Official Complied/street Registered R35gtr


Recommended Posts

  • Replies 271
  • Created
  • Last Reply

Top Posters In This Topic

Having said that the rb is late 80's technology and i believe it did very well to last this long....time to step aside i think, although the R35 is yet to be proven 100%. Time will tell...i have complete faith.

I love my RB engines.....

But its 2008 and Nissan had to come out with something new, or be swamped

fine for the 1% that can afford the 35 but the other 99% can have an RB GTR right now with the necessary upgrades to give them similar power which will see them thru for the next 10 years or so until the 35 becomes affordable.

What someone needs to do is come up with an RB package that gives similar kind of midrange to the VR38, as thats the key for it being so quick in such a heavy car...midrange and lots of it! :)

Nice...

All though no where near the 400rwkw mark the gt30 .82 on the rb30 makes 200rwkw at 3500rpm and 256rwkw at 4000rpm with 19psi.

Would be interesting to see what sort of power a well sorted rb30det with a pair of 2530's could make.

hahaha joel u love the 25/30 :):D and have good reason too.... i thin someone needs to make a custom t3 manifold and strap on some turbos on the 35 and wind up the boost!!!

Nice...All though no where near the 400rwkw mark the gt30 .82 on the rb30 makes 200rwkw at 3500rpm and 256rwkw at 4000rpm with 19psi.

Would be interesting to see what sort of power a well sorted rb30det with a pair of 2530's could make.

Its the transient response that would blow you away. While its possible to hold a car on the dyno and let it build boost to make a power and torque figure at a given rpm, get it out on the road at 1500rpm and nail the throttle in fourth gear. That tells the complete story :)

Edited by Martin Donnon
Its the transient response that would blow you away. While its possible to hold a car on the dyno and let it build boost to make a power and torque figure at a given rpm, get it out on the road at 1500rpm and nail the throttle in fourth gear. That tells the complete story :(

Exactly.. There's really no replacement for displacement. :)

martin

what is the max rev limit for this engine. 7500 rpm?

also do you have the software to unlock the 03 350z ecu to raise the rev limit on that?

would something like >>This<< help

Look its a forum, anyone can have an opinion - but heres the facts....

R35 GTR Stock

0-100km/h - 3.5 sec

0-400M - 11.5/11.6sec @ 120-122mph

Now to get this pace from an R32/33/34 GTR you will need -

TD05 kit/GT2540 turbochargers or similar running 1.5 bar boost

700cc+ fuel injectors

Upgraded fuel pump

Programmable management FC or similar with a correctly carried out tune

Front pipes

Full exhaust system with cat removal

Upgraded twin/triple clutch

Possible intercooler upgrade

and be prepared to build an engine for it in the very near future...

as well as being in a constantly harrassed and defectable car :merli:

This isnt a guess. We have done our fair share of GTR modification over the years.

Nissan have done a very good job of building a genuine supercar that thankfully DOESNT need a bucket of cash thrown at it to make it go like it should.

That is the true value of R35 :laugh:

So basically you get 911 turbo performance for the boxter pricetag?

And there's still plenty of scope for upgrades without having to rip it to pieces and kill the package.

Like you say, sounds like the real deal to me.

I love my RB25DET

I believe on a scale of 'bang for buck', modding the RB engines is far cheaper with sufficient gains.

Maybe in a couple of decades when the R35 and any mods are more affordable ............

yeah I agree to some extent Reuben - but you simply can't compare the R35 with anything that has ever existed previously - it is in a whole new league. Fact is you don't need to mod it - with a tune they are making 350rwkw - much more that you can use on the street anyhow.

yeah I agree to some extent Reuben - but you simply can't compare the R35 with anything that has ever existed previously - it is in a whole new league. Fact is you don't need to mod it - with a tune they are making 350rwkw - much more that you can use on the street anyhow.

Yeah, I shoudl have also added "... when the R35 is also proven after years of service"

:merli:

yeah I agree to some extent Reuben - but you simply can't compare the R35 with anything that has ever existed previously - it is in a whole new league. Fact is you don't need to mod it - with a tune they are making 350rwkw - much more that you can use on the street anyhow.

We're not Andrew, but others on here are!

I'm sure when the 34 GTR first came out, peeps were saying the same thing........"plenty of power, you don't need to mod it"....who you trying to kid :merli:

Exactly.. There's really no replacement for displacement. :P

Then again... VW have done a very reasonable job of making an engine that's short on displacement punch well above it's weight. VW call it TSI, but it makes more sense when I say... a supercharger and a turbocharger combined to work as one.

The VW Golf GT/TSI runs a 1.4L four cylinder TSI engine that makes 125kw and 240nm of torque, the bulk of the later at just 1500rpm till 5000rpm. Driven 'normally' it can also return figures of under 6.0L/100. It's even more fun when it comes with a DSG gearbox.

Not exactly R35 GTR territory, but good for the daily commute, very impressive economy (handy when paying 1.50+per L) and much quicker than a few fleet Commodore owners were expecting :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
    • And if you have to drill the oil block, then just drill it for 1/4" and tap it BSP and get a 1/8 to 1/4 BSP bush. The Nissan sender will go straight in and the bush will suit the newly tapped hole. And it will be real strong, to boot.
    • No it doesn't. It just needs an ezy-out to pull that broken bit of alloy out of the hole and presto chango - it will be back to being a 1/8" hole tapped NPT. as per @MBS206 recco. That would be for making what you had in alloy, in steel. If you wanted to do just that instead of remote mounting like @Duncan and I have been pushing. A steel fitting would be unbreakable (compared to that tragically skinny little alloy adapter). But remote mounting would almost certainly be 10x better. Small engineering shops abound all over the place. A lathe and 10 minutes of time = 2x six packs.
×
×
  • Create New...