Jump to content
SAU Community

Recommended Posts

  • Replies 72
  • Created
  • Last Reply

Top Posters In This Topic

I only just solved a shocking miss and sputtering above 3k rpm that had been getting steadily worse. But it was totally intermittent, the car would drive fine for long periods then just come to a sputtering halt in 30 seconds flat.

Determined to find the problem i changed the plugs, no go

I took it to my local speed shop and they told me i had the wrong plugs in and wrong gap. Stick new ones in... no go

For some reason my suspicion was that it wasnt ignition. Because when i stick it in a high gear at low speed (give it some high ignition load) it would just pull out. Then splutter again at a bout 3200rpm, then pull smooth to redline. Other times it would break down so much it wouldnt pull past 2000rpm.

The solution? Air flow meter. Pull it out and give it a good spraying of contact cleaner. Car now drives better than ever.

Red17

I am not the best person to answer this queston as I have not had a dyno run with my skyline yet and am south east, I can however recommend Hypertech Autosports

7 Trade Place Vermont VIC 3133 (03) 9874 8866 Ask for Arnold

  • 2 weeks later...

Just out of interest When I started my car this morning when it was cold it started to idle roughly again, so I unpluged the AFM and the revs went up but the car ran beautifuly. whats got me that my Auto elec said they had it tested & calibrated it and it was fine, I have my doubts. now to find a loan one so I can test it...

Hi I had the same problem with my R34 it was missing like hell at about 4800 to 5000 revs.I replaced the plugs with Platinum and gapped them at 0.8.

I also suspected one of the coils might have been arking across to the cylinder head as well so I taped the stem of the coil pack with insulation tape,Hey presto going like a train no miss.

Maybe I should take the tape of the packs to see if it gets the miss back.

I had a very similar problem with a Telstra Ghia a few years ago.

So maybe worth a try.

WLD747

I had similar problems too you, changed and gapped plugs numerous times, coil packs checked, AFM, then raised the boost and it made it worse, backed it back and it was better. Then installed and dynoed tuned with a SAFC and fixed it. Basically for my car, it was getting to much fuel to drink. Are your plugs black?

And whilst not only fixing the problem, i scored some nice power gains.

I will be doing some further tuning soon.

http://www.skylinesaustralia.com/forums/sh...&threadid=22703

Robo's - thanks for the advise cause im getting a PFC asap which will enable me to tune my afr. I found out today from another mechanic that my car is extremely rich so yeh hopefully problem will disapear soon.

I recommend to anyone with mild mods to get a new ECU or a SAFC to balance the ECU. Because it makes sense. 1 -4RPM not much fuel so boost quick and hard then 4PRM + too much fuel and boogs down.

Thanks in advance Rob

AK

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • How much have you lowered?  I had 350Z springs in the rear and was able to pull the camber into factory spec with the factory arms on the rear, obviously the front ran negative camber as it isn't adjustable, but rotating the wheels regularly evened out the wear.
    • Either the installer needs to come back, you need an auto electrician, or you need to learn automotive electricals yourself.   First step Id look at is where that big thing came out of, is there still things unplugged at that location? Maybe they just forgot to put a relay in or something?
    • Well, this is probably where a wiring diagram and a multimeter come into play.
    • I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
×
×
  • Create New...