Jump to content
SAU Community

R34 Gt Rims On R33 Gts-t

Sonic speed

By Sonic speed,
in Exterior & Interior Styling

 Share

Recommended Posts

Sonic speed Enthusiast

Sonic speed

Posted
Posted

Hey all,

As the above would imply I have a set of r34 GTT rims and went to put them on my 1997 GTST, however on doing so I found that the rims don't clear the brake calipers. Is this normal as other people have done it and said they don't think you need spacers. If not, why arent they clearing over the brakes? Seem odd? This has only happened for the front brakes so far, although I havent tried the rears.

Thanks in advance....

Link to comment
https://www.sau.com.au/forums/topic/236186-r34-gt-rims-on-r33-gts-t/
Share on other sites
maximumrpm Mentor

maximumrpm

Posted
Posted
Hey all,

As the above would imply I have a set of r34 GTT rims and went to put them on my 1997 GTST, however on doing so I found that the rims don't clear the brake calipers. Is this normal as other people have done it and said they don't think you need spacers. If not, why arent they clearing over the brakes? Seem odd? This has only happened for the front brakes so far, although I havent tried the rears.

Thanks in advance....

i needed spacers as well just to clear the front brakes ..i have a r33 gtst s1

Sonic speed Enthusiast

Sonic speed

Posted
  • Author
Posted

Okay, so I also talked to a mate who had the same problem. He said thats what he noticed, however he was told that you just chuck the car back on the ground and go for a drive down the street and it will just shake the calipers a bit. Then after that you use a bit of wet and dry. What do you all make of that idea? Is yours a 1997 model though DNGRUS (Nice car)?

Basti Grand Master

Basti

Posted
Posted

not a good idea mate. dont drive on them. i've got gtt wheels on my series 1 and they clear. i think its just a little bit of variation in individual cars. i've got almost no clearance at all. just get spacers. 5mm wont hurt anyone

cheez Mentor

cheez

Posted
Posted

5mm/3mm spacers arent noticeable and make no difference in grip length of nuts that are in the dangerous to drive on bracket.

get them and be done with it, driving around with the wrong offsets can do more damage than good. if u want a set, i got a set at home off my old 33. pm me

bubba Grand Master

bubba

Posted
Posted

I had problems with GTT rims binding on my stock 32 brakes and needed 3mm spacers, but when I put 33 brakes on the calipers were obviously a little further out from the hub and was enough to clear without spacers (albeit by approx. 1mm).

croat Mentor

croat

Posted
Posted

when i bought my r33 gtst it had these wheels. i saw that on the brakes the wheels had rubber about 2mm of the caplier off. it was fine and has never caused any probs, you cant even notice it. i personally would shavesome of the caliper face off..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 89GTR_VA
      Crank/No Start - R32 GTR Chassis with R34 RB26

      By 89GTR_VA · Posted

      Apologies for the long post, but needed somewhere to lay out the entire timeline of events and actions taken:   I've got an 89 GTR with a R34 RB in it. It's been running great all year, driven probably 500KM in the last month. It's not my daily driver, just a weekend fun car.    Build info: R34 RB26 - HKS 2.7 stroker kit, HKS adjustable cam gears, HKS turbo upgrades, Trust intercooler, R34 factory DENSO 440cc injectors, JUN chipped/tuned R32 ECU. All of this work was performed in Japan back in 2019.    Thursday 10/2/25 - It's a nice day and decided I'll drive it to work, I start it up in the garage and I notice it took a few extra cranks and sounded a bit funny. I figure maybe it was just because it was a pretty chilly morning. I pull it out into the driveway to warm up a bit before leaving. As I leave the driveway, it feels very off and sounds like a misfire. I pull it back in the garage to deal with after work and take the daily to work. I was able to diagnose it as a cylinder 5 misfire with the old spark plug test (unplugging each plug until a sound change with the engine running). I take off the whole ignition system, ignitor, plugs, spark. *Important note, it is still on the R32 ignition system with the separate ignitor system. I test each system with a multi-meter and nothing presents as a smoking gun. I put it all back together and it starts up no issue. I go ahead and order the PRP R35 ignition conversion kit. It should arrive today (10/13/25)   Friday 10/3/25 - Another nice day, car starts up great and drives great all day. Very pleased that everything seems to be OK   Sunday 10/5/25 - Decided I'll take it to play some golf, load up and drive to the course about 25 minutes away. Drives wonderful the whole way there, I pull in the parking lot and the engine completely comes to a stop. I do not recall if it sputtered at all, but just remember all of the sudden the engine was off. I roll it into a parking spot, try to crank it back on and nothing.  It'll crank and crank and not even try to start. End up getting it towed back to my house and push it up into the garage.    Items I have checked: Fuel in the tank Fuel Pump relay Fuel pump fuse  Spark Plugs & gap Coil packs Ignitor    I know the cylinders are getting fuel as the plugs smell like fuel after a start attempt. I tried spraying starter fluid into the manifold and cranking and not even a sputter.    I decided to do the live CAS test (removing the the CAS, ignition on and spinning the CAS stalk to see if the injectors pulse and spark is active). All of the injectors were pulsing and I have spark at the plug. The half-moon end of the CAS did seem very loose, I'm not sure how much play is supposed to be there, but it was more than I expected. There was no in/out play of the shaft, just the tip end that is pinned on had quite a bit of play.    CAS Play video   When I put the CAS back in, I stupidly did not re-time the engine. I know I need to do that tonight, however, I do not think it will start given it seemingly was not the issue. My plan is to do the PRP R35 coil kit and retime the engine at the same time.    I plan on ordering the Haltech Nexus Plug-in ECU once they are available again, but ideally would like to get this sorted before firing the parts cannon at it and potentially adding more variables.    Anything glaring that I am missing here, I'm a bit at a loss?          
    • GTSBoy
      98 R34GTT 4k engine stumble

      By GTSBoy · Posted

      Get it on a dyno. Get something logging Consult. Run it up and find out what is causing it.
    • BuiltNotBought
      Freddy Plenum vs Genuine options RB25

      By BuiltNotBought · Posted

      Looking for a plenum for rb25 de+t neo  Not looking to push much power maybe 300kw at the wheels, is there much difference in flow for Freddy “Greddy style” compared to original Greddy or options like Proflow or Otaku garage?    I won’t be porting the de Neo head for now as I think it’ll be fine 280-300rwkw but appreciate the help and any experiences anyone has between them and any advice. Thanks  Looking at this plenum for now below 
    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      engine wise almost no mods: stock ecu Greddy front mount intercooler Greddy forward facing intake w R33 TB stock fuel system, stock injectors, rail etc. Kakimoto racing hyper 3 inch exhaust system Apexi intake filter New NGK –R BCPRES (.8 gap) plugs  
    • PranK
      The New Official S A U - N S W Spotted Thread

      By PranK · Posted

      Nice one @Pac - looks like a fair few 1600's there! 
×
×
  • Create New...