Jump to content
SAU Community

Recommended Posts

Read the post by rips a few up. I wouldn't worry at all about using rb25 head studs.

Yeah i seen that , 8 second defs made me feel better but usually 8 seconds could be rebuilt motors after so many runs etc..

Ok this is excellent feed back... This makes me feel alot better about it.

Did you guys torque the bolts to the recommended setting or go a lil extra?

From memory it was like 85

Dont go more torque than in the manual.

Any more may distort the deck of the block which you dont want.

Also remember the RB30 block is thinner and weaker around the bolt holes, the block material is also a lot softer than studs, so removing thread to fit a bigger stud only weakens your blocks deck area for the sake of adding more bolt strength which is already more than adequate.

The deck will distort more than the bolts can stretch.

We are using RB25 studs on our 600KW build.....any give will be from the block deck distorting to hold the studs/head down, not weak studs stretching......

Go back to page 1, 2 well known builders who do this for a reason, if there was a gain going bigger, they would have been doing it.

Edited by GTRPSI

This is what was tripping me out abit too, no tuner i spoke to said they have ever encountered the casting mark where the idler goes... they said they are all flat .

The casting gets in the way of mine... it wasnt a big issue we made it flat but dno if that helps u guys distinguish what type of block it is.

2wqeq9e.jpg

This is what was tripping me out abit too, no tuner i spoke to said they have ever encountered the casting mark where the idler goes... they said they are all flat .

The casting gets in the way of mine... it wasnt a big issue we made it flat but dno if that helps u guys distinguish what type of block it is.

2wqeq9e.jpg

there is at least one thread on here with a block with the same issue, I think he was in the usa, cos if you are in oz the obvious thing to do would have been get another block.

There are some posts (i think they may have been here) on the web where people have built washer type spacers of fabricated some steel to compensate for the block finish as in the pics above and it worked just fine.

sall good we were able to make it flat and fabricate a solid spacer for it . :)

that's the proper way to do it.

as alrady said, you can get a washer style pacer made, but being timing belt, youd want to be 100% perpendicular.

Couldn't you get sleeves made up to slip into the head bolt holes so you can just use rb25 ones?

You don't need sleeves. It's the dowels that align the head to the block, not the bolts or studs.
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Well, fun day was had, I finally found a house that will do me just fine, 1980's brick build, but with full fresh renovations, plus new colour bond fencing all round so puppies are incoming 🐕, and water tanks for the garden, and it's located in West Goulburn..... @Duncan 🫡, so day trips to Wakie to watch cars going Zoom will be on the cards In the end it cost well under my budget and was actually better than alot of the more expensive joints I was looking at, it is in a good area, close enough to the shops, public transport, and the Wollondilly River Weir,  and the great walking paths along the river, but far enough away from town to see minimal traffic The deposit is dropped, the conveyancer is conveyancing and I should get the keys in a week or 2 as the property is currently unoccupied  As with everything I own, I'm doing up a modifications list, as it doesn't have solar, that is first up on the big list, all of the panels and enough batteries to keep the joint warm, or cool, followed by a largish carport out the front, the small list, which will start as soon as I have keys, is some security stuff, like cameras, screens, and the usual "crazy prepper" additions that weird old people like (mouse holes to stick shot guns out of, and the usual man traps that the average person installs for the unsuspecting and unwanted guests 🤣) The gardens front and back are OK, but, not to my standards or liking, so landscaping will be a fun job to start getting into, so when spring is sprung I'll do a heap of planting, lots of natives and vegetables is the plan, the old owners were more "Old English Garden" type, so basically Roses and other weird looking things that are destined for the green waste bin One thing that is staying garden wise is a nice established hedge out the front, it is about 5 foot tall and covers the whole front of the property from prying eyes As for the car hoist, the roof in the garage has some height to it, but, I'll need to get an installer out to see what can be done, width wise may be a issue, but my building inspector will be getting back to me over the next week with his recommendations  Small, but cosy     
    • I tried to get in contact before I went to QLD you didn’t respond, then I tried to contact you in r31 club.  I thought you fell off the earth or something haha.  I will grab it off you but unknown when I will be up that way 
    • I think that might be in the question. He is going very low, and I think the standard GTR ones are simple tripod joints (like the rear NA/S chassis ones), not proper CVs (like R chassis turbo/GTR ones). Proper CVs take the misalignment better than tripods.
    • Do you still need the wiper motor and stuff?
    • I haven't used the Crank Motorsport ones, but can I ask why not use standard gtr/gts4 axles at the front? They would easily cope with that power level. BTW.....sounds like quite the project!
×
×
  • Create New...