Jump to content
SAU Community

Recommended Posts

  • Replies 260
  • Created
  • Last Reply

Top Posters In This Topic

Annoyed there is no cruise, that was one of the best cruise to go on. Cops dont really pick on anyone. Was good just having a car full of mates and a esky and just cruising.

But yeah scs should be about sitting down relaxing and letting people enjoy what u have done with your car. Shouldnt be about how many trophies u get but more about letting other people have a closer look at the car u have built with your taste. Theres no point coming on here winging, do what u like to your car and if other ppl dont like it dont worry.

my 2c

sorry cara,

suppose my comment was outta line.

just dont expect too much resect among the v8 lovers out there.

thats the only thing hoding me back, the bagging.....

id love to go out there and rip a stomper burnout.......hmmmm...how much entry?

apology accepted craig.

i entered last year and had no issues...........it didnt do the burnouts last year but there were a couple of imports and they had no issues either............

v8's can do badly aswell ive seen it

entry now is 170

170 ;)

170 entry

100 stockies

700 when clutch finally blows....

80 tow truck

11ty billion on lost ego...

its very expensive...but very tempting....entry forms @ sprints?

yup they sure....entry fee went up a couple weeks ago i was too busy and missed the early bird deadline :)

everyone just needs to punch themselves in the eye and take a seat for 5 minutes.

im kind of keen on scs, just not sure right now. ill see who else on here is 100% on it.

im 100%

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...