Jump to content
SAU Community

Recommended Posts

Go to one of the tune shops that can tell the difference between a GTR and a GTS-T.

the usual suspects would be

C Red

SST

Speedworks

Some people may have a beef with some of the shops but they can all check a line over and tell you what's wrong.

Also get a cylinder leakage test done , is a good indication of engine .

Cheers

Ken

Link to comment
https://www.sau.com.au/forums/topic/23766-skylinerac-check/#findComment-508702
Share on other sites

it would be unlikely that they'll come out and have a look at the car.

when i first purchased my Line i had it looked over by the guys at Cypher Industries. cost me 70 bucks but the more or less stripped the whole car and even checked for panel damage on the inside bla bla bla

took close to 2 hours and included a lengthy report. all in all i reckon it was money well spent

Link to comment
https://www.sau.com.au/forums/topic/23766-skylinerac-check/#findComment-508731
Share on other sites

Yeah i found a nice skyline, just wanna get it checked, thanks for that G0DF4Th3R and gtrKen, i didn't know Speedworks was in Ossie park, conveniently the seller and I both work in ossie park :P

Nah,

I've sorta canned that idea, purely cause it was going to take to long, too much hassle, and considering i could get a turbo car with selling mine and using the money that was going to be used on the engine.

I change my mind too much!!!

Kris

Link to comment
https://www.sau.com.au/forums/topic/23766-skylinerac-check/#findComment-508769
Share on other sites

Originally posted by gtrken

Also get a cylinder leakage test done , is a good indication of engine .

How is this test done? Is it the oil around the outside of the engine? Can you tell the engine is leaking just by lookin at it , apart from "oh theres oil around the engine" cause sellers can wipe it clean just before someone buys it. (Sorry, another one of my dumb questions!)

Thanx y'all!

Link to comment
https://www.sau.com.au/forums/topic/23766-skylinerac-check/#findComment-509065
Share on other sites

Originally posted by Phat^Beatz

How is this test done? Is it the oil around the outside of the engine? Can you tell the engine is leaking just by lookin at it , apart from "oh theres oil around the engine" cause sellers can wipe it clean just before someone buys it.  (Sorry, another one of my dumb questions!)

Thanx y'all!

Remove spark plugs and run compressed air thru a special gauge which tells how much blowby, valve, head gasket etc problems you may have.

Cheers

Ken

Link to comment
https://www.sau.com.au/forums/topic/23766-skylinerac-check/#findComment-509388
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nope, I don't like the look of ND RF, or any ND really, I don't like their faces or arses, why, because of their "modern" lines, the NC, whilst "modernish" has a more rounded shape that I like Well, that's how my overly judgemental eyes see it anyway  
    • Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
    • I definitely know the first rule here, look first, ask second. I've seen many people get roasted 😂 I found a few diagrams for the RB, but I'm yet to come across one for the VQ. From what I have read, the pump gets the +12v along with the FPCM, and it's the negative wire that gets passed through the resistor to regulate the voltage. So I assume I can just ground the negative wire at the pump to eliminate the FPCM control. But I really wanted to see the VQ circuit diagram first to make sure I understood it correctly. Once the new pump is in I'll do some testing to see how it behaves, and in the meantime, I'll keep looking for a wiring diagram. Thanks for your help mate, your time is greatly appreciated.    
    • Maybe? I have the Supercheap ToolPro low thingo. It has a somewhat smaller diameter lifting "bowl" than you would expect on a workshop grade trolley jack, and a split rubber pad to suit that diameter. It clears the "N1" style skirts I have. Probably wouldn't if the jack's bowl and a suitably larger rubber block were in use. Having said that though.....you only need the rubber block to exist on the inner side of the pinchweld, so could carve away any rubber that fouled the skirt, leaving some there for "insurance" </simples>
    • I used to do that (sills with rubber jack block).. ... then I got side skirts, and there's no way for the jack to actually work there, the jack pad itself on the jack is too big. Is the answer to use a... smaller (?) jack? Hmmm.
×
×
  • Create New...