Jump to content
SAU Community

Recommended Posts

give ya missus a couple beams, grab a snatch n strap n pull the bubs out with the dr :wave: actually use the rex 4x4 be safer :)

HAHAHA trust SAU to bring this back to cars.

But seriously... if you use a 'snatch' n strap (pardon the pun) don't use the rexy would only pull the skin off a rice pudding. This is a SKYLINE site after all :D

I have no idea who you are, but best of luck anyway, braver than me.

Edited by Stagstock
  • Replies 174
  • Created
  • Last Reply

Top Posters In This Topic

trust me i am not looking forward to pushing it out, just yeah a whole head :) OMG

but they reckon the pain goes away once there out and your holding them.

a hot tip...its unnatural for a woman to give birth laying down on a bed...get a gym mat on the floor and kneel on it supporting your upper body with a chair...Stace made it look easy as when the water broke Elsie was out in 17 minutes. Let gravity do some of the work for you.

;)

no fuukin way ill be watchin my missus push it out.t

ill be there, but eyes definately shut, or ill vomit.

+1 Would ruin our 'relations' for a long while I would think... I just couldnt look at it the same again.

I saw my sister born, that fcked me up for a long while with the women. :(

Edited by Stagstock

9!!!!!!

Seriously man.... Scarred for Life

All in all though.. gives me something to try and forget lol

'reaches for the dimer'

Edited by Stagstock

Yeah, thats the trouble with being the eldest of 6 especially when there's 9 years between my closest sibling, the rest are all still kids really.

Sorry for highjacking the thread pokie.. I'll stop now.. I promise.

The last half dozen posts on this thread are mega funny, I laughed out loud at work. Jonnyboy89 that is the funniest post I have ever read... Oh man, gold!

So as to not be put off sex for the rest of my life post kids my missus can get cut open. No hot-dog down a hallway for me.

can I remind some of you filthy buggers that this is a pregnant female's thread who doesn't need to hear the polluted crap that comes from your mouths!

I've put it to the other Mods but as far as I'm concerned, someone needs a holiday!

At a minimum, these posts belong in Wasteland!

Far out watch your mouths you dirty pricks!

EDIT: Beaten by Pete :)

+1 ;\

I've been present at the birth of a child before, and I saw the birthing. Theres nothing wrong with that... sure its not a simple, clean experience, but neither are a bunch of other things in life. It certainly changes your perspective, cause now the baby is now 13 years old...

Having said that, I don't plan to have kids.... ;P Not because of childbirth incidentally. I just think children aren't worth the hassle >:laugh: (Listen to some Bill Hicks if u dont get it) (oh and parents, plz dont get offended, its just my opinion)

Love

-Uncle D

Sorry if I offended anyone... it also wasn't meant to be distastefull. I mearly described how she looked when she was born. Didn't see much in it honestly.. Anyway.. apologies to all concerned.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...