Jump to content
SAU Community

Recommended Posts

Hey guys, don't post on here much (if at all), but i hope u can still help. I searched, i didn't find.

Didnt know if this should go in forced induction or n/a forum, since its got aspects of both... There should be an electrical/ecu subforum.

Basically, my friend has gone and purchased pretty much everything he needs to turbocharge his n/a S1 R33 (1993) off these forums (bar dump pipe, which he is getting tomorrow). We swapped the injectors and ecu over and now his car wont start. Everything is connected the way it was before and it doesn't sound like the fuel pump is priming, so that would be my first guess.

All the turbo parts (bar intercooler piping, which isn't attached) are off the same car, which was running at the time the parts were removed but I'm not sure if the car was an S1 or an S2.

So, basically, is there any reason why a S1 RB25DE R33 running just the ecu and injectors from a RB25DET R33 wont start, remembering it may possibly be s2 ecu? Is there any wiring/control differences in the fuel pump/ecu circuits, or could the ecu just be a dud?

Only mods to his car are pod filter, exhaust, steering wheel, rims and springs, so none of these should be making the difference.

EDIT: He got the turbo bits off "R34GTFOUR" so if you could reply stating if S1 or S2, I was the one who said I would be putting it together :P

Edited by Mitchd03

The pump should still work, the only difference is a relay for upping the voltage to it under load, that doesn't come into effect at idle.

Where is the AFM hooked up? You need a closed system so the air goes through it and gives a reference voltage for the ECU.

Also has he got the turbo fuel pump fitted? He'll run into dramas with it leaning out if it's not already in.

Yep grab a GTSt pump and fuel regulator (or did you get the complete injectors and rail?) if you can...but saying that, your car isn't starting for another reason....as it will still idle on a GTS pump just fine

Well all we did last night was remove fuel rail and insert the new GTST injectors and then plug in the GTST Ecu, is it possible we need to reset the settings by unconnecting the battery? Could it also be something to do with a fuse?

Ok, it starts and idles now, but it blows light grey smoke, and misfires. Smells like there's no catalytic converter.

Could this be wrong fuel pressure for the turbo ecu? If so, what is the correct fuel pressure, as we are using an N/A fuel press reg.

Remember, its an RB25DE with T injectors and ecu.

EDIT: Just took it for a drive and its definitely running way too rich, the cat light came on when taking it to higher (4-5k) revs, huge exhaust pops when shifting gears, hunting for idle etc. but the misfiring got better (wasn't cured) at higher rpm (around 3)

Stuck injector? Wrong fuel pressure? Fuel pump? (remember, NO BOOST, its still an n/a, no more air than before, therefore no more fuel needed, so pump should be capable for now)

Edited by Kyro

why are you installing injectors before the turbo.... the ecu is tuned to run the injectors with the forced induction, all the problems you have are the sign of over fueling, if you's keep running it u'll burn out the cat (thats why the light is coming on, it's getting to hot), install all the components needed Turbo, intercooler, pump, FPR...

why are you installing injectors before the turbo.... the ecu is tuned to run the injectors with the forced induction, all the problems you have are the sign of over fueling, if you's keep running it u'll burn out the cat (thats why the light is coming on, it's getting to hot), install all the components needed Turbo, intercooler, pump, FPR...

The ecu adds fuel as the AFM reads more air, if the ecu just smashed more fuel in all the time, the car would be rich (like this) when not under boost, then stoich when boost hit

You can have a turbocharged car with ecu and injectors designed to run boost, remove the turbo and it will run fine.

I know this is true, i've done it twice. One time to my ford Telstar TX5 turbo. It uses an air flow meter, just like nissan use. The only difference is the tx5 has one massive injector instead of smaller ones on each cylinder (like a carbie). The turbo blew an oil seal, i pulled turbo out, reconnected the afm and it runs fine, its just really slow and loud.

The second time to my z31 300zx. It was a VG30E, naturally aspirated. I had turbo injectors and a turbo ecu lying around, waiting to get a turbo. I had to pull the intake manifold off, so i changed injectors and ecu at the same time. The car runs exactly the same as it did before (misfiring, a little rich, hunts at idle, backfiring on overrun, it's always done this, its an '84 model car). Old injectors were ~180cc, new ones are 269cc (they sound tiny i know, but higher fuel pressure than RB25DE) and the ecu is calibrated to those injectors. We did exactly what i did to the zed, yet i got a completely different result, and my assumption was the fuel pressure regulator, as with the RB swap we kept the n/a fuel pressure reg, but on my VG30E I swapped the regulator with the turbo one (as i got a complete rail).

And now that an N/A ecu is running bigger Turbo injectors, when the turbo ecu couldn't run them... it doesn't make sense. If you put big injectors in the car goes really rich, anyone who has tuned a car should know this. You then have to shorten the injector times to get it to run stoich again, which is what the turbo ecu does.

Bah!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How much have you lowered?  I had 350Z springs in the rear and was able to pull the camber into factory spec with the factory arms on the rear, obviously the front ran negative camber as it isn't adjustable, but rotating the wheels regularly evened out the wear.
    • Either the installer needs to come back, you need an auto electrician, or you need to learn automotive electricals yourself.   First step Id look at is where that big thing came out of, is there still things unplugged at that location? Maybe they just forgot to put a relay in or something?
    • Well, this is probably where a wiring diagram and a multimeter come into play.
    • I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
×
×
  • Create New...