Jump to content
SAU Community

Recommended Posts

  • Replies 77
  • Created
  • Last Reply

Top Posters In This Topic

Very tidy Scott, but what's the red switch for if you don't mind my asking.

for my NOS bottles...... hahahaha nah just kidding..... its for my boost controller. Have low set on about 8psi and high on 12-13psi... love that switch deffinately comes in handy =]

Those pics are pretty old.. I tooks a few more the other night but only difference is shortened gear knob and Nismo badge

Skyline-13.jpg

Skyline-14.jpg

hey mates..just found this guy from south east melbourne selling really nice interior for r33 and r32, friendly and patient guy. cost me around $120 but havent fitted in yet, as i'm busy for the x'mas. Anyway if anyone is interested, feel free to drop him an email at [email protected] "ekkoperformance"..cheers

post-58226-1229856804_thumb.jpg

the whole interior cost you $120? what does the package comes with

Whole set comes with:

2 x Front door trims, 1 passenger 1 driver

2 x Rear arm rest trims, 1 passenger 1 driver

1 x Centre console lid

1 x Glove box trim

1 x Set of instructions on how to install :P

My interior

IMGP1788.jpg

9fd0.jpg

Just thought it should be known that this R33 has a FULL Cusco roll cage (from what I can see) perfectly integrated to the standard trim... this is really beautiful in it's own right... how much police trouble have you had from this?! :rofl:

PSI Parts also noticed this, as I would expect :P

shits all over my painted interior n shit

  • 1 month later...
Just thought it should be known that this R33 has a FULL Cusco roll cage (from what I can see) perfectly integrated to the standard trim... this is really beautiful in it's own right... how much police trouble have you had from this?! :D

PSI Parts also noticed this, as I would expect :)

Sure did :banana:

Just going back to the cage, would this be CAMS approved? I seem to remember CAMS only allows two bends in each corner bar for structural reasons? (Yes I can't be bothered looking at my CAMS manual)

Yep, cheaper rego too :P

So am I right in saying you can rip your rear seats out and all you have to do is re-register your car as a 2 seater.

Or is there more involved..ie; RTA inspections, etc.

I wanna rip out everything I can!

So am I right in saying you can rip your rear seats out and all you have to do is re-register your car as a 2 seater.

Or is there more involved..ie; RTA inspections, etc.

I wanna rip out everything I can!

If you remove the rear seats and register as a 2 seater, the rear seat belts need to be removed as well as far as I know

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...