Jump to content
SAU Community

Help Please

RPR33

By RPR33,
in Engines & Forced Induction

 Share

Recommended Posts

RPR33 Community Regular

RPR33

Posted
Posted

Hey guys my sr is making a tapping noise around 2-3k it started last night when I was like 25k's from home I drove home keeping it under 3000rpms.

If it is the bearing how good are the odds that I'm gonna need a rebuild? it was still driving fine when I got home? do you think It'll be right to just change bearings?

Cheers,

Russ

Link to comment
https://www.sau.com.au/forums/topic/238844-help-please/
Share on other sites
Strik3r Experienced

Strik3r

Posted
Posted

are you doing the work yourself or not ? If your paying someone to do it, once you have the engine out and open, it might be worth throwing forgies and a set of rods in there.. ($2k) since you're probably going to be paying that much in labour. Put a decent head gasket in there too.

in any case, if your not gonna replace parts, get them checked out thoroughly.. i'd say your crank will need machining at the least

Link to comment
https://www.sau.com.au/forums/topic/238844-help-please/#findComment-4174582
Share on other sites
R31Nismoid Grand Master

R31Nismoid

Posted
Posted

Well your looking @ 1k for motor in/out before you start.

Then, if fitting new bearings your gonna have to machine everything to suit the 4 new ones you'll have to put in etc.

So 3k would be in the ball park as you cant really just swap one bearing, you do them all and freshen it all up.

You sure its a bearing?

Link to comment
https://www.sau.com.au/forums/topic/238844-help-please/#findComment-4174759
Share on other sites
RPR33 Community Regular

RPR33

Posted
  • Author
Posted

pretty sure.. Its not something I have done before myself but a friend of mine done his in his silvia and said it sounds the same.. he's pretty in the know with these cars as he drifts and built his monstar, It seems to idle fine however if I give it a little rev it starts a knocking sound at 2-3rpms then clears up.. its a pretty loud knock very easy to here. and just sounds like it's coming from the head or front of the motor!

cheers

Russ

Link to comment
https://www.sau.com.au/forums/topic/238844-help-please/#findComment-4174858
Share on other sites
R31Nismoid Grand Master

R31Nismoid

Posted
Posted

could be something in the head?

Im not up with whats inside SR heads, maybe a valve or something?

I thought a bearing knock didnt go away with RPM (as i did here a XR6t here and the knock only got louder with RPM), could well be wrong there

Link to comment
https://www.sau.com.au/forums/topic/238844-help-please/#findComment-4175019
Share on other sites
shaunzo101 Enthusiast

shaunzo101

Posted
Posted

If you were giving it a good thrash just before it happened, its extremely highly likely its the bearings. Perhaps just look around on forums on here and boostcruising for someone who just wants to get rid of their sr, then all you have to do is take out the old one and put in the one you buy, then you have a whole motor sitting there for spares. I know my mate could have picked up a working ca for 150 im not sure on prices for the sr. But first thing you should do before you make any moves is get advice from a qualified mechanic and go from there.

Link to comment
https://www.sau.com.au/forums/topic/238844-help-please/#findComment-4175111
Share on other sites
dmr Mentor

dmr

Posted
Posted (edited)
I thought a bearing knock didnt go away with RPM (as i did here a XR6t here and the knock only got louder with RPM), could well be wrong there

spot on.

i would get a professional to check it out before you start spending big cash.

Edited by dmr
Link to comment
https://www.sau.com.au/forums/topic/238844-help-please/#findComment-4175620
Share on other sites
super_s13 Community Regular

super_s13

Posted
Posted

Possibly a rocker arm. My ca was doing a similiar thing but it was the big end bearings gone. Soon after that i threw a rod. Go and get it checked from a mechanic. ust to be sure. I am not sure if the guys on here are right about the bearing noise would not go away as mine always did. As soon as i got over a certain rpm it wnt away. DR drift tunes a mates car and heard the same noise on a smaller scale up in darwin and then stopped tuning but he said it was a bearing knock and that goes away.

Link to comment
https://www.sau.com.au/forums/topic/238844-help-please/#findComment-4177494
Share on other sites
BezerkR32 Veteran

BezerkR32

Posted
Posted

its alot more difficult to diagnose a engine noise in a full alloy block as the knock resinates through it.

best way to do it is to take load of cylinder by unplugging coil pack plug or injector harness one at a time. if noise lessens on a particular cylinder when you do this you can be pretty sure it is down stairs.

SRs are renound for this, usually because the sump has been pushed up and seals the oil pick-up. Look under the car and see if the sump is dinted.

I did a big end set in a GTIR last week, cost the guy $800. this included genuine bearings, synthetic oil & filter. Done it in the car. No probs. Only thing to check is that the crank isnt damaged. otherwise its engine out and full build.

where would that sound come from? mine seems to be coming from the top of the engine on the exhuast side!!! dam car only had it a week :blink:
Link to comment
https://www.sau.com.au/forums/topic/238844-help-please/#findComment-4177795
Share on other sites
  • 2 weeks later...
shaunzo101 Enthusiast

shaunzo101

Posted
Posted
The bearing noise would be there all the time man, there is no way that you feck a bearing and only hear it at a certain RPM.

i work with them all day lol.

Well actually, i KNOW from personal experience, that in my commodore (yes its not an sr) the big end bearings went on that, and before the motor died it made a knocking sound as you increased the revs and especially under load with the sound getting greater at heavier throttle. So yes, you do hear it at a certain rpm before the motor dies of course. The big end bearings can set your motors life short instantly, over very short time or could extend over a longer period of time depending on the severity of the damage to the bearings.

Link to comment
https://www.sau.com.au/forums/topic/238844-help-please/#findComment-4200919
Share on other sites
joeleo87 Experienced

joeleo87

Posted
Posted
yeh I have no plans on spending cash at the moment LOL

It sounds like this.

this is not from my car but one on youtube doing the same thing.

Watta you think it is?

hmm that noise is weird as hell.....

any luck with the mechanic???

Link to comment
https://www.sau.com.au/forums/topic/238844-help-please/#findComment-4203266
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • QB6SAGR
      Tein Circuit Master- rebuild worth it?

      By QB6SAGR · Posted

      Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
    • funkymonkey
      Howdy Y'all

      By funkymonkey · Posted

      Nice car! I’m glad folks in the US have gotten past the FnF and are buying real cool cars like the 260RS I was with a bunch of mates in Portland about a year ago and spotted a green Stagea (just a regular 2.5T AWD) parked about 2 blocks away and they were like “a what?” So I made a bet with them for a round of beers and said “ok one of you run down there and tell me if the steering wheel is on the correct side” 5 mins later the American comes trudging back up the hill and goes “he’s right guys. Ok what beer do you want?”
    • Dose Pipe Sutututu
      Starting again

      By Dose Pipe Sutututu · Posted

      Should replace OR drop the tank, give it's good clean. Might be worth replacing that entire fuel level/pump/cradle thing with this: https://frenchysperformancegarage.com/products/fpg-s13-180sx-r32gtst-single-pump-hanger-kit-billet-hat-6-v3-fpg-089?gQT=2  
    • R33_Guy
      Speed Sensor replacement

      By R33_Guy · Posted

      Thank you so much for the help
    • GTSBoy
      Speed Sensor replacement

      By GTSBoy · Posted

      Yes it is ATF. I quote @Duncan "it takes a good synthentic auto trans fluid like Castrol Transmax Z" It's not a diff. It's a transfer case. Totally different thing. Yes, fluid will come out the sender hole. No you do not really need to drain it. Just pull the old, quickly poke the new, clean up and top up. But realistically, you should probably take the opportunity to change it anyway.
×
×
  • Create New...