Jump to content
SAU Community

Recommended Posts

mine was put in when complied. its located/screws inside my stock speakers and the anchor points are welded to the chassis under the parcel shelf. i have seen some brackets though that were in the sales sections but no idea how they were fitted.

Thanks heaps, i just have to find some so i can get my defect cleared, its the last thing i need, do you reckon you could take some pics of yours for me so i can see how they fit on?

Anyone got the 2 child restraint brackets they wanna sell cheap or at least send me a pic of some fitted so i can see how they go so i can get some made up. PLEASE !!!!

Skyline off the road & desperately wanna get it back out there again.

heres my restraints. problem with mine is because its inside the speaker and where its rivited to the chassis its nearly impossible to remove my parcel shelf..ha. i probbly could remove it but i gave up. like i said ive seen other brakets out there that are different to mine so im not sure if this is the propper way or the poxy way.

post-1726-1223546508_thumb.jpg

heres my restraints. problem with mine is because its inside the speaker and where its rivited to the chassis its nearly impossible to remove my parcel shelf..ha. i probbly could remove it but i gave up. like i said ive seen other brakets out there that are different to mine so im not sure if this is the propper way or the poxy way.

thanks heaps, lol now i might be able to get them fitted myself, once i get hold of some.

Alright guys don't fret, I'll take the pictures of mine later today check back at 9pm at the latest, if it's not up PM me....I might have forgotten but I'll prob be on the forums around that time

Alright guys don't fret, I'll take the pictures of mine later today check back at 9pm at the latest, if it's not up PM me....I might have forgotten but I'll prob be on the forums around that time

sounds good, thanks.

contact isaso.com.au they should be able to sell you the correct R33 child restraint brackets. however, these should have been fitted at compliance. so you could always check your compliance plate, then ring that shop and tell them you got defected because they didn't fit child restraints and could they please give you a set. but it may be easier to just get some from isaso.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Haha luckily we don't have emissions, inspections, or any laws against power adders here. They only thing they somewhat keep an eye out for are ridiculously loud exhausts. 
    • Just wanted to pop in an update on my setup. The CD swap has been great, I love the mazworks housing for the overall simplicity. I ended up sealing my trans tunnel with a thin sheet of aluminum reused some of the holes on the trans tunnel, and laid some window sealing EPS foam around the edges. Works great, really quieted things down and sealed up the car.  As for the power comment. Right now I am also running about 650whp. with the way the bell housing is attached to the face of the transmission I have zero doubts it would be fine, mainly because the input shaft and main shaft bearings are seated into the bell housing adapter. This means the load is NOT on the bolts to maintain the power, rather into he casing of the bell housing; Yes the bolts are doing some work there, but with both shafts locked in zero worries.  End of the day, the Mazworks solution is the easiest and safest. no need to take your trans to a shop to get milled perfectly, it fits with minimal clearancing, and you can use all your existing clutch and flywheel.  Driving wise the CD has been great compared to the big box, I'll probably swap my final drive at some point. The serial 9 shifter is gooooood, my only qualm is how tight it is, it takes a fair bit to get use to, 5th and 6th are a bit eh/hard to find at times, but maybe I need re-adjusting, and I think my clutch master is very tired and needs a rebuild. 
    • If you are keen, have a look at my build thread. Car is for sale for the right money or straight swap for a F80 M3 LCI.
    • Welcome mate.  No point in over thinking it, buying any one of those cars you mentioned is not a smart or logical choice with the availability of many "better" (re price to performance) cars available to you.  The heart wants what the heart wants, buy whatever it leads you too.
    • Hey everyone! Im so grateful to be apart of this community and ill do my best to be apart of this. Firstly, i'm not disclosing my real name due to in real life circumstances surrounding my privacy and public image (sorry lol) Secondly, The only thing personal I am willing to share is that I'm from Sydney and a descendant of one of Sydneys largest mortgage firms. I got gifted my first ever car, a 2022 Porsche Cayenne and I love it to death. Ive been driving it for about 5 or 6 months now and honestly Im so grateful for my parents for gifting me this vehicle. However recently I've been working my ass off to afford my second car (which I need help deciding soooooo community help me out please?). Once decided, im planning to try modify it myself. Recent I've been thinking about getting a Skyline, particularly a 25GT or GT-V, yes I know overrated as hell, but I'm also considering a Chaser which I recently came to love. However my dream is to one day own a 180SX (So hard to find clean versions and im not really into importing).  Lastly before I send this off, I want to apologize if I sound tacky or pretentious. I try not to and want to genuinely learn from everyone and anyone. (Im no expert in this area) Thanks for reading!
×
×
  • Create New...