Jump to content
SAU Community

Recommended Posts

well i can confirm the sr20 plug fitting a r33. when i got mine for my 33 from autobarn the part number listed for the r33 was the same as the n14 and n15 SSS pulsar (i have a SSS pulsar as well and got them to look up a price on it while i was there and the part number was the same, and then when i went out to the car and looked at it it looked the same)

as for the r33 and r34 being the same, i'm not sure.

price wise i think the ngk sensor from autobarn cost me about $120

Link to comment
https://www.sau.com.au/forums/topic/239244-o2-sensors/#findComment-4193485
Share on other sites

if your gunna pay a massive amount of money for an 02 sensor you might aswell wait for the genuwine nissan r33 one to come in....

other than that i used a $70 EL falcon 02 sensor and it works great, just had to snip and tie the wires together then electrical tape them up..... now saving about 25% on my fuel bill..... if your going to have to cut the wires anyway you might as well go for the cheapest one you can get.... end of the day an 02 sensor is an 02 sensor,,,, only switches on and off.... nothing complicated about it, aslong as it has 3 wires and the thread is the same as your dump pipe thread....

Link to comment
https://www.sau.com.au/forums/topic/239244-o2-sensors/#findComment-4195594
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...