Jump to content
SAU Community

Recommended Posts

This gets asked a lot, so here they are according to Nissan workshop manuals:

Rb26:

Balancer Bolt - 446-466nm (ouch!)

Flywheel Bolt - 124-152nm

Clutch Bolt - 34-44nm

Rb25:

Balancer Bolt - 142-152

Flywheel Bolt - 124-152nm

Clutch Bolt - 34-44nm

good luck getting 450nm on the RB26 bolt without a tension wrench designed to do wheel studs up on a Euclid 170T dump truck.

I do them 150nm then get a pipe over it for another 1/4 of a turn....never had one come loose.

what about putting some lock tight ova the thred? is this recomended i dont really want a pully popping out to say hello threw my bonnet at 8000rpm

DO NOT put Loctite or any other anerobic compound on them. ARP moly lube only please.

Hey mate,

Its 30mm for a RB26..

Cheers,

Thanks Johno.

what about putting some lock tight ova the thred? is this recomended i dont really want a pully popping out to say hello threw my bonnet at 8000rpm

You're pretty safe if u torque up the bolt to the above specs, loctite won't hurt, more of an assurance, but sucks to be the next person to rip the bolt out...haha.

(in saying that, some people are quite religious about using loctite)

  • 4 months later...

just looking over this ... the balance bolt should be replaced with every clutch . i've looked at the threads on 25's and 26's and came to the conclusion it was a stretch bolt because it thins out close to head of the bolt. its just good practice . get it the right way first .

good luck getting 450nm on the RB26 bolt without a tension wrench designed to do wheel studs up on a Euclid 170T dump truck.

I do them 150nm then get a pipe over it for another 1/4 of a turn....never had one come loose.

+1 I did it that way too before I put my engine in.

Pole was 4 meters long=sweet!

  • 8 months later...
  • 3 years later...
  • 3 years later...

Anyone know the thread size for RB Flywheel bolts? Bought my RB20 for $20 and it has been sitting outside for the last 5 years so has some rust/filth in the threads in the crank. Looking go buy a tap to clean them up. Cheers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...