Jump to content
SAU Community

Recommended Posts

Hi everyone,

Recently on a long track, the Apexi AVC-R (EBC) fitted in my R34 GTT, clocked 302km/h as the top speed during the length of the Journey, i have an after market Nismo Meter which shows speeds upto 300Km/h but unfortunately i was lookin on the track and not the speedometer. Although I do remember shifting to the fifth gear cause the revs were upto 6.7 on the 4th gear (never had to floor car above 4th gear) and after shifting into 5th i was still pushing on the pedal.

As for other mods, the car has a Front Mount Intercooler, the Apexi EBC as listed above, full 3.5inch cat back exhaust and was running it on 0.76 Kg/cm2 Boost.

Do you guys think the AVC-R has recorded some false value? or is 302km/h a comfortable speed for the RB25DETT engine? the car is 1998 so the engine is not brand new?

Any expert opinion or comments guys? im confused?

Link to comment
https://www.sau.com.au/forums/topic/240286-r34-gtt-top-speed/
Share on other sites

whats your diff ratio, and tire size? work out your theoretical geared top speed

then you will need to find out your drag coefficient which isnt usually very accessible data unless you either

1. have a wind tunnel

2. find your actual top speed and have accurate power figures as well

ps. 302kmh is approx 187mph thats pretty fast for a standard skyline

two main components for calculating theoretical top speed

rolling resistance

drag due to air resistance

rolling resistance is fairly linear so easy to calculate

drag due to air resistance has a cube relationship to speed.

so the increase of 250kmh to 300kmh is a factor of 1.2

the power increase you need is the cube of this factor (1.2) = 1.728

using very average numbers for coefficient of friction, average combustion efficiency and average drivetrain losses, you need 408hp (flywheel hp) to reach 187mph. very rough numbers though but just to give you the scale of things.

Edited by clip14

Hmm interesting thread... *subscribing*

I hit 265km/hr on a pretty worked RB25 before... that was the reading off my F-CON Navigator (I only have a 180km/hr dash), and am not sure if its entirely accurate.

...not with a 3.6 diff

BTW Thelma & Louise didn't even reach that speed in the last few seconds in the T-Bird!

In reply to the post above,

the T-Bird after leaving the cliff will accelerate to the point of terminal velocity where the wind resistance balances out the gravitational pull.

The T-Bird's terminal velocity would be a maximum of 60m/sec = 135mph = 216Km/Hr >_<

  • 6 months later...
speed limter? no mention of an aftermarket ecu?? and nothing about removing speed limiter.. so i assume max speed at 180... if not i don't think you'd get that speed on 0.76 Boost...

The speed limiter isn't in place and its an after market Nismo Speedometer so reads upto 320km/h and yes its calibrated!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • Bunnings would have just handed you your money back on that one!
    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...