Jump to content
SAU Community

Recommended Posts

Having a huge cleanout of 32 GTR parts. I have got rid of a fair bit of stuff but I still have a little left over.

All parts are in Melb. Frieght at buyer expense. I will get sizes and weight for you but you have to price the freight up and I will confirm it once you actually want it.

Gauges and Electronics

Apexi Electronic Oil pressure and Exhaust temp gauges and senders with max warning $300 pair

HKS Vein Pressure Controller - Very Rare and wanted.

Deletes the need for afm's and can control fuel rates $500 Comes with looms and sensors

HKS Turbo timer $80 plugs straight into dash loom

Blitz and Mines ECU's x2 $100 each

Wheels

Nismo LMTG2 rims 17*9 with 16 offset. Perfect for a 32 gtr. 2 very good tyres, 2 unroadworthy. They have a few scuffs on the rims. $1250

Set R32 GTR rims 16*8 with unroadworthy tyres. A couple gutter rashes. $500

Set 265/35/18 semi comps. Bought off Racepace secondhand and I never used them. Still a couple trackdays in them $100

Engine/Drivetrain

Rear drive shafts $150 Good boots

Blitz external venting BOV's $175 pair with std gtr pipe to mount on.

3 GTR radiators $80 each Same as gtst.

Fuel tank with hangers/pump/sender/filler neck $200 Stop serging on your gtst as the pump is mounted a lot better.

GTR fuel pumps x2 $100 each

RB26dett crank, oil pump, rods, plus all the other parts associated with crack from 32 $400 Removed form engine that had a cracked ring. Sold head and block.

Suspension/Brakes

Tein HA height and damper shocks and springs $500

STD shocks with aftermarket springs $200

Pair machined 324mm rotors $150

Tein springs. Suit drift car $100 Very stiff.

324mm slotted disks-new, spacer kit to run 324mm disks and overhauled calipers and braided lines with heaps of set used performance pads Upgrading to big 355mm brembo's. Best upgrade you can do without spending thousands of dollars. Almost as good as GTR brembos. Same pad width just looses 5mm on height at the bottom. No brake fade running 1.23 at Sandown and 1.52 and PI or 20 min sessions running 1.10's at Wakefield with a few laps to cool engine oil down in the middle.

Will fit R32 gtst, gtr and R33 gtst

$650

Interior

Dash boards. Small boubles in front of passenger $40 each

2 sets nissan floor mats $80 each

GTR interior trims. A few small scuffs $150

Body

LH door window w/tint $40

GTR fuel cap door $50

Rear Bumper reo $60

RH door $30 bare

Big duel element aluminium wing $100

Please don't ask for other stuff as this all I have. No swaps either or low ballers. I won't get back to you if you offer stupid prices. Will budge on some stuff but no others. If you know what it looks like please don't ask for pics for silly things.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...