Jump to content
SAU Community

Recommended Posts

Impressive results on a mainline dyno there Lee, you should see 265-270 on a DD machine.

Im going back to the drawing board, Wastegate was WIDE open but still pumping close to 20+psi. So ive decided to Go external Gate modded onto my DMAX manifold so i can regulate boost alot better. I could just wack on a .82 rear with a larger internal gate but i want to retain as much response as i can get my hands on so i'm keeping the .63 with looked fairly responsive and going external gate.

Much appreciated to Martin and Mark for the help. Top Blokes.

EDIT: martin seemed to love my setup, i was a bit unsure about the size of the bastard. :D

Cheers Ryan Last time there was only 4kw difference on Aussies DD but either way i'm happy with the power to weight. I must have just missed you today i left at 2.30pm. I'm sure you will get your beast sorted in no time did you run it up on the Dyno?

Lee

  • Replies 143
  • Created
  • Last Reply

Top Posters In This Topic

Impressive results on a mainline dyno there Lee, you should see 265-270 on a DD machine.

Im going back to the drawing board, Wastegate was WIDE open but still pumping close to 20+psi. So ive decided to Go external Gate modded onto my DMAX manifold so i can regulate boost alot better. I could just wack on a .82 rear with a larger internal gate but i want to retain as much response as i can get my hands on so i'm keeping the .63 with looked fairly responsive and going external gate.

Much appreciated to Martin and Mark for the help. Top Blokes.

EDIT: martin seemed to love my setup, i was a bit unsure about the size of the bastard. :D

so what power did u end up making Ryan???

external gate FTW!!!!

ARE U GONNER HAVE A SCREAMER OR PLUMB IT BACK??

Before we could even do any sort of power run i wanted him to check what boost it was running because of previous experience with turbo's like this and wastegates etc, Before the turbo went on i got the wastegate machined out to its limit and i made the dump pipe to clear the massive flap but wasn't enough. Definetly going External gate, With a screamer eventually plumbed back. hehe

I made a custom Bell mouth from scratch, Very free flowing. Ahh well... Just annoyed there is a bit of a delay. I tell ya what, It sounded f*kn awesome on the dyno. Will be an animal once its finished. Was great just driving the car again after 6 weeks.

Edited by Ryanrb25

this subject is pretty interesting.

I swapped the 34 GTR bellmouth style dumps for a pair of short splits (using the -5's) and found that occasionally she'd creep up to 18 or 19psi..........not sure if it's an obstruction issue with the gate.

I was considering going back to the 34 GTR bellmouths with the new setup that's just about to go on.

Gary Cook (Sydney Kid) was telling me not to waste my time with short splits & to stick with a decent bellmouth unless I plan on using the long split style like the Trust setup (approx 400mm splits)..........AM Performance can make a similar setup as the Trust's.

Thoughts guys??

Definetly an interesting subject pete, i wish my camera worked at the moment, i'd take some photo's of the dump pipe i made for this turbo, Very wide, very smooth blend, fairly large dump pipe. Took a couple of hours of heating and bending to get it right. Im really not a fan of the splits unless it had a really really good blend. Usually alot of those split dump pipes have somewhat of a wall to hit before it goes through a tiny pipe.

Heslo, definetly sounded like very very strong power. Curve was awesome. I'll write back to your PM in a tic mate.

Edited by Ryanrb25

yeah maybe the little splits are good for small diameter gates but I think they tend to fail on bigger gates hence why I'm thinking bellmouth more & more.

Is it true the 34 GTR dumps are bigger than the 32 & 33's?

Cheers Ryan!

Pete, I'll be going the long split style. Seen AM Performance work close up and spoken to Andrew and he does some great work and knows his shit. Pretty cheap too. But as always the end decision comes up to you :P

A little OT but.... :P

Pete usually the problem with the splits is the area behind the gate. When the flap opens it tends to block part of the opening which tends to result in slightly more boost or worse case creep.

Shaun was telling me he's had a play with splits/bell mouths on the dyno and didn't notice any difference (power etc) between the two (providing boost is kept constant). The only time the split was beneficial is when the exhaust is marginal for the power i.e 3" for 300rwkw+ and you run a screamer.

Ryan.. Here's my dump. Can be improved upon but can't complain for under $100.

Would prefer a 70ish or 45degree bend with the wastegate section a little longer and merging smootly in to the pipe. Maybe the sharpish push in to the stream of the turbine gas is creating a little back pressure in front of the turbine wheel allowing greater flow for the wastegate, hence boost drop to ~2psi above the actuators rating.

post-382-1226313860_thumb.jpg

post-382-1226313868_thumb.jpg

post-382-1226313874_thumb.jpg

Mine is very simular Joel. That's impressive tho, I'm sure the black paint isn't there anymore tho hehe.

agree with your thoughts on flow and the flap not opening 100 percent blocking alot of the flow into the split pipe.

Edited by Ryanrb25
Home made. ;)

The black paint is actually still there..... On the outside. :D

haha, just razzing ya.........looks like a very good effort.......and welds don't have to be pretty, just have good penetration (well that's what my Dad says, he's a boilermaker)

i love custom items!!! i have a AWSOME customer x-member.... added value to my car!

You like that do ya hehe.

haha, just razzing ya.........looks like a very good effort.......and welds don't have to be pretty, just have good penetration (well that's what my Dad says, he's a boilermaker)

That's right, you could have the prettiest welds but if there's no penetration then its completely useless.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
    • Well the articals keep saying a Q50s (Skyline in Japan) with a new Manual gearbox. I like the talk about the new looks with the round tail lights. I hope they bring back the retro look like they did with the Z
    • Off the back of feedback we have decided to mix up this next Motorkhana at Avalon to have some targeted skills practice for beginners to advanced. Saturday 6th September 2025 8:30am Capped 26 entries Standard Entry Fee: $89 Members Entry Fee: $55 (SAU Victoria Only) Entries Close: Friday 5th February  Where: 55 beach road Avalon. https://maps.app.goo.gl/HNUE3EuNue3sJxh38 Entries: Limited to 26 entrants (Passengers allowed over the age of 14 with a signed disclaimer and same safety gear) Disclaimer: Download  Please electronically sign and email to [email protected] or print and hand in and Driver Sign In. To compete in this event you will require A valid  AASA General Speed licence or (Day license via the AASA Website for $50) MA Licenses are no longer accepted by AASA https://aasa.com.au/  A helmet, long sleeve clothing and a 1KG mounted fire extinguisher recommended (But not Mandatory). Further details within Supp Regs on the enty link. Entry Link > https://www.sauvic.com.au/entry/deca/20250906 You can bring and have a passenger in the car but they need to comply to the same safety and clothing as driver. Bring your car and get to battle others, win, lose or draw. I can guarantee you will have lots of fun. Any questions email [email protected] Entry List: 1.Anna S 2. Luke S 3. Jesse Givens-Lamb 4. Luca Stamatescu 5. Madeleine Stamatescu    
    • Wanna rewrite all of that in, say, 2 or 3 separate sentences, so that we can read it?
×
×
  • Create New...