Jump to content
SAU Community

Recommended Posts

Hi all, yes i do realise there is a number of threads about idle issues which i have read through but none of them come out with a successful solution. I have an r33 series 2 rb25, the car will usually have that hunting issue where its going between 0 and 1000rpm, sometimes it settles at idle and other times it will just stall. I have cleaned out the iac valve completely, replaced the gasket on the iac valve and secured all hoses i have touched and it hasn't made any difference at all. Does anyone know what to do to fix this?

Link to comment
https://www.sau.com.au/forums/topic/240711-stalling-idle-troubles-any-ideas/
Share on other sites

disconnect battery (bolt attaches to boot frame)

pump the brake pedal a few times

reconnect battery (bolt attaches to boot frame)

start car and let idle

it should sort itself out

if it doesnt go see a mechanic

base timing etc is probably whack

should be 15det BTDC at idle

i'm still tipping vacuum leak.

there are numerous hoses that might not have been checked from the front of the plenum to the carbon canister and under the cross-over pipe. this is worth another check. apologies if you have checked every single one.

i'm still tipping vacuum leak.

there are numerous hoses that might not have been checked from the front of the plenum to the carbon canister and under the cross-over pipe. this is worth another check. apologies if you have checked every single one.

you would hear a vacume leak though.... i did with mine.....

clean afm, change plugs,clean throttle body, do you have standard bov? i recon the most important culprit is the 02 sensor..... that $70 f#&ker stuffs things up when not working,,,,,, fixed my idle prob and now gives me better fuel economy...

sure it will paul.

i have had at least 4 deteriorating hoses on my car (over the years) and i have lost count of the cars of friends with splits in various vacuum hoses that hunt at idle. immediately idling fine after replacing the hose or trimming it back.

the last time i got the car back from the panel shop they forgot to reconnect one of the hoses to the carbon canister but due to its location under the snorkel it was a job to find in the dark with a little torch.

does the vehicle have any mods firstly and does it blow black smoke from exhaust at idle. if so make sure you have not blown an intercooler pipe. also could be a faulty afm. hope this helps

its fairly stock, apart from front mount intercooler and boost controller, it doesnt blow any black smoke at idle. im going to look into checking the error codes i was given that idea by a friend.

disconnect battery (bolt attaches to boot frame)

pump the brake pedal a few times

reconnect battery (bolt attaches to boot frame)

start car and let idle

it should sort itself out

if it doesnt go see a mechanic

base timing etc is probably whack

should be 15det BTDC at idle

thanks il give that a go tomorrow. theres a place near me called rpm performance north of brisbane, so that was my last resort if i couldnt sort it out myself.

you would hear a vacume leak though.... i did with mine.....

clean afm, change plugs,clean throttle body, do you have standard bov? i recon the most important culprit is the 02 sensor..... that $70 f#&ker stuffs things up when not working,,,,,, fixed my idle prob and now gives me better fuel economy...

il give this a go tomorrow as well. the bov is stock. after i try all this if im still having problems, il look into new 02 sensor.

$20 its the 02 sensor, especially if it hasnt been changed...... diconecting it wont change a thing if its not working in the first place paulr32...... what ever it ends up to be is just general standard maintenance anyway..... alll these things should be done anyway

  • 7 months later...

PLEASE HELP!!!!!! :)

Im having the same problem with the idle fluctuating (hunting). changed plugs cleaned iac throttle aac etc etc and it hunted usually between 1500-500 just changed the coils to splitfires now it does it 1000rpm-2000rpm. it isnt consistent it is intermitent. also car will just stall when clutch has been pushed in (giving it to it or sensible driving) checked ALL Vac lines aswell. also some times it will rev to roughly (i say that coz its never on the same spot its a bitch of a thing to trace) 3500-4500 and before i changed the coils it misfired then until the boost climbed it wouldnt rev anywhere near as quick then slingshot me (very dangerous in the wet) now after the coils are changed it does the same thing but it doesnt sound like its missfiring its alot quiter but same feeling NOTE: day night rain hail or shine it will do this problem sometimes does it when the car is cold but definatly when it has warmed up. sorry for the billion words hope it makes some sense

car details:

Series 1 r33 manual gtst

RB25det

splitfire coils

standard ecu

afm looks good and clean

vac hoses checked and some replaced

standard BOV

t4 turbo (was on the car when i bought it) standard exhuast manifold

standard exhaust

also just one more thing if someone has a couple of pics of a stockish engine bay can they post them

Edited by Melbourne93R33
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
    • Literally looks like direct port nitrous haha
×
×
  • Create New...