Jump to content
SAU Community

Recommended Posts

what are you trying to do eaxctly?

if you are looking to put straight video in there is a easier way. otherwise it will be RGBs and you will need a scope to find what you are after. do you know what video and sync signals looks like?

Link to comment
https://www.sau.com.au/forums/topic/240888-r34-in-dash-lcd/#findComment-4214849
Share on other sites

I want to swap the the pop up lcd for a GTR MFD i have bought.

I have bought the sub harness from nissan that goes from the MFD to the connectors behing the guage cluster the old pop up screen has two connectors and the new one has three and they are not the same. so i have male and female connectors form the old harness and want to use them

Basically i wanted the pinout of the connectors behind the guage cluster so i could pull out each pin from the (pop up lcd sub harness) connectors and put the connectors on the MFD sub harness.

The (pop up lcd sub harness) has about 24 wires and 4 free spots for wires, and the MFD harness has 48 wires. I have another connector from a Honda harness i can use for the rest of the wires.

Know the stock Navi unit is useless here but i wanted to connect all the wires for it so that later when i replace it i can use the MFD as the screen for the new navi unit.

I have a scope and the R34 GTR service manual has pics of what the signal looks like but to replicate the signals it gives instuctions to press buttons on the navi unit and mine is FAULTY (i get some blue screen with JAP writing and cant make it turn off or anything) so i dont think I'll be able to work it out that way.

I was just hoping someone might know which wire is which to save me time trying to work it out myself.

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/240888-r34-in-dash-lcd/#findComment-4218117
Share on other sites

http://flatout.main.jp/driving/parts/bnr34mfd/

The above site is in Japanese so run it through a translater. its a guy in Japan with a gtt that has put in a mfd but as far as i can remember he did not have the sat nav to start with so i hope it helps. Failing that pm me with your email address as i have two PDF's with how to wire them as well as an operations manual.

Cheers

Ross

Link to comment
https://www.sau.com.au/forums/topic/240888-r34-in-dash-lcd/#findComment-4219966
Share on other sites

I want to swap the the pop up lcd for a GTR MFD i have bought.

I have bought the sub harness from nissan that goes from the MFD to the connectors behing the guage cluster the old pop up screen has two connectors and the new one has three and they are not the same. so i have male and female connectors form the old harness and want to use them

Basically i wanted the pinout of the connectors behind the guage cluster so i could pull out each pin from the (pop up lcd sub harness) connectors and put the connectors on the MFD sub harness.

The (pop up lcd sub harness) has about 24 wires and 4 free spots for wires, and the MFD harness has 48 wires. I have another connector from a Honda harness i can use for the rest of the wires.

Know the stock Navi unit is useless here but i wanted to connect all the wires for it so that later when i replace it i can use the MFD as the screen for the new navi unit.

I have a scope and the R34 GTR service manual has pics of what the signal looks like but to replicate the signals it gives instuctions to press buttons on the navi unit and mine is FAULTY (i get some blue screen with JAP writing and cant make it turn off or anything) so i dont think I'll be able to work it out that way.

I was just hoping someone might know which wire is which to save me time trying to work it out myself.

Thanks.

ok so you want the GTR unit to be fully operational?

if so then there is a diagram for it on here. as for the rest depends on how you go about it. you can do comp video into it OR RGBs with fiddling. both of those require teh MFD to be modded.

don't worry about the GTT harness - disconnect it and leave it be.

Link to comment
https://www.sau.com.au/forums/topic/240888-r34-in-dash-lcd/#findComment-4221547
Share on other sites

i got it from the for sale forum here, but if ure after one i would suggest importmonster.com.au or slidewizeimports.com.au

I paid $1100

If you but one you will most likely not get the piece of harness with it but you can get it from nissan for about $200, the part number for it is in one of my other posts in the Tutorials and DIY section

Link to comment
https://www.sau.com.au/forums/topic/240888-r34-in-dash-lcd/#findComment-4234229
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...a bit a "development" on the brakes. I spoke to the guys where i get brakes from...and they are saying that 296mm EBC are for R34 GT-T. I then went to their site: https://www.ebcbrakes.com/vehicle/uk-row/NISSAN/Skyline (R34)/ and search for my car(R34 GT 1998 - it has GTT brakes) and it show me this USR1229 number and they are rly 296mm rotors... So now iam rly confused... The rotors i have now on the car are 310mm asi shown... So where is the problem? Does the whole EBC got it wrong or my calipers are just...idk know what?  
    • Oh What the hell, I used to get a "are you sure you want to reply, this thread is XX months old" message. Maybe a software update remove that. My bad.
    • This is a recipe for disaster* Note: Disaster is relative. The thing that often gets lost in threads like this is what is considered acceptable poke and compromise between what one person considers 'good' looks and what someone else does. The quoted specs would sit absurdly outside the guards with the spacers mentioned and need  REALLY thin tyres and a LOT of camber AND rolling the guards to fit. Some people love this. Some people consider this a ruined car. One thing is for certain though, rolling the guards is pretty much mandatory for any 'good' fitment (of either variety). It is often the difference between any fitment remotely close to the guards. "Not to mention the rears were like a mm from hitting the coilovers." I have a question though - This spec is VERY close to what I was planning to buy relative to the inboard suspension - I have an offset measuring tool on the way to confirm it. When you say "like a mm" do you mean literally 1mm? Or 2mm? Cause that's enough clearance for me in the rear :p I actually found the more limiting factor ISNT the coilover but the actual suspension arms. Did you take a look at how close those were?
    • @GTSBoy yeah sorry i know thery are known for colors bud those DBA are too in colors 🙂 Green will be good enough for me  
    • That's my life. Past-Duncan has a lot to answer for
×
×
  • Create New...