Jump to content
SAU Community

Recommended Posts

Hey guys, first thread here so be gentle :cool:

bought an r33 recently, and in the past week its been blowing a bit of white smoke when I change gears after it comes onto boost. Did a heap of research and have showed some mates who know what they're on about (I don't too much) and we've come to the conclusion its a gone turbo seal.

first of all..

its a 1996 rb25 r33gts-t

fmic

full 3" mandrel exhaust

manual boost controller (that hisses on idle.. getting that fixed :laugh: )

bov

stock ecu

im going to either a) get the turbo reconditioned, hi flowed and a steel wheel put into it, or b) buy a brand new, and probably a bit bigger turbo and get that put on.

don't know too much about turbo imports, only the very basics... so my questions are..

What do you think the best option is? I'm not looking for huge power, eventually 250rwkw or so will be all i'm after (so far haha). If i buy an aftermarket turbo, will it require an aftermarket ecu to be properly tuned?

is there anything i'm missing? any ideas/feedback greatly appreciated.

Link to comment
https://www.sau.com.au/forums/topic/240955-what-turbo-for-me-r33gts-t/
Share on other sites

Whats the budget? thats the first place to start

Aftermarket turbo, requires ECU... hell, even the stock turbo can benefit noticeable from a decent ECU/Tune.

Budget dictates where you go... because 250rwkw really is injectors & AFM upgrade too.

interesting is had a different afm, guessing it a z32 afm, but it definatly has the standard ecu? Find that out first. 4k...hmmm maybe hks 28/35, pfc 555cc injectors n tune..?

Oh forgot to say it has aftermarket pod and an AFM on it, not sure what the afm is though =/ mechanic said the pod was installed badly with too much coating oil which has half - f**ked the afm =/

Budget is 4k ish

thanks mate :/

stock ECU = stock AFM, simple as that.

Oil doesnt mean a stuffed AFM either. A simple clean is probably all thats required.

4k = no turbo upgrade!

ECU - 1500

Tune - 500

Turbo - 1600+

AFM - 350

Injectors - 750

Tot: 4700 - without even putting on labour, another 1k id say.

And given current world pricing etc, injectors may well be more

You could skimp out on a cheap hi-flow/bigger replacement turbo, however they are laggier and less responsive than a decent hi-flow/bigger replacement... so in my book not really worth putting on.

Id say put another stock one on for now and keep saving

cheers

it helps if u shop around, if i went for like hiflow or kkr turbo, my upgrade would have only cost me slightly over 4k

most of these parts were 2nd hand, but in good condition

pfc 1000

injectors 550

afm 220

ebc 350

tune 450

= 2570

but i spent 2500 on a hks gt-rs

so in the end 5k+

also saved a bit on labour as i got [Michael] on the forums to help me install the turbo for a carton haha :/

mate said 1000-1200 all up for all the gear + installed.

Iv bought an apexi power FC that will be arriving on wednesday.

il be booking into godzilla motorsport and getting it tuned there, and i was gonna buy some more goodies and get him to chuck them in for me as well.

What should i get next? it has an AFM on it but a mechanic told me its nearly dead or on its way out. new afm? good afm is pretty necessary isnt it.?

EBC? injectors? fuel pump? splitfires? mechanic also told me coil packs werent in best nick.

all help again appreciated

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...